Rainbow Electronics MAX16024 User Manual
Page 2
MAX16023/MAX16024
Battery-Backup Circuits with
Regulated Output Voltage
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(V
CC
= 1.53V to 5.5V, V
BATT
= 3V, reset not asserted, T
A
= T
J
= -40°C to +85°C, C
OUT
= 10µF, unless otherwise noted. Typical val-
ues are at T
A
= T
J
= +25°C.) (Note 2)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
V
CC
, BATT, OUT to GND..........................................-0.3V to +6V
RESET, PFO, BATT ON (all open drain)
to GND..................................................................-0.3V to +6V
RESET, PFO, BATT ON (all push-pull)
to GND .................................................-0.3V to (V
OUT
+ 0.3V)
PFI, CEIN, CEOUT to GND .......................-0.3V to (V
OUT
+ 0.3V)
MR to GND .................................................-0.3V to (V
CC
+ 0.3V)
Input Current
V
CC
Peak Current.....................................................................1A
V
CC
Continuous Current ...............................................250mA
BATT Peak Current .......................................................500mA
BATT Continuous Current ...............................................70mA
Output Current
OUT Short Circuit to GND Duration ....................................10s
RESET, BATT ON, CEOUT..............................................20mA
Continuous Power Dissipation (T
A
= +70°C)
8-Pin TDFN (derate 24.4mW/°C above +70°C) .........1951mW
10-Pin TDFN (derate 24.4mW/°C above +70°C) .......1951mW
Thermal Resistance (Note 1)
θ
JA
(8-Pin and 10-Pin TDFN)........................................41°C/W
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Operating Voltage Range
V
CC,
V
BATT
(Note 3)
1.53
5.5
V
LDO = 1.2V
4.3
6
LDO = 1.8V
4.7
7
LDO = 2.5V
5.2
7.5
LDO = 3V
5.5
8
V
CC
= LDO + 0.5V,
no load
LDO = 3.3V
5.7
8
LDO = 1.2V
16
20
LDO = 1.8V
16
21
LDO = 2.5V
16
18.1
LDO = 3V
17
18.6
Supply Current
I
CC
V
CC
= LDO + 0.5V,
I
OUT
= 20mA
LDO = 3.3V
17
19
µA
Supply Current in Battery-Backup
Mode
I
BATT
V
CC
= 0, V
BATT
= 3V,
no dropout, no load
3.5
5.26
µA
BATT Standby Current
V
CC
> V
BATT
+ 0.2V
-0.01
+0.01
µA
SET Reference Voltage
V
SET
MAX16024_TB_, V
CC
= 2.2V
1.144
1.2
1.272
V
SET Input Leakage Current
MAX16024_TB_, SET = 1.2V
-20
+20
nA
Output Voltage Range
V
OUT
MAX16024_TB_, V
CC
> V
OUT
1.8
5.25
V
LDO = 1.2V
1.145
1.2
1.270
LDO = 1.8V
1.704
1.8
1.900
LDO = 2.5V
2.368
2.5
2.634
LDO = 3V
2.837
3
3.165
Output Voltage Accuracy
I
OUT
= 1mA
LDO = 3.3V
3.114
3.3
3.482
V
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-
layer board. For detailed information on package thermal considerations, refer to
www.maxim-ic.com/thermal-tutorial
.