Pin description (continued), Typical application circuits, Detailed description – Rainbow Electronics MAX1543 User Manual

Page 10

Advertising
background image

MAX1542/MAX1543

TFT LCD DC-to-DC Converter with
Operational Amplifiers

10

______________________________________________________________________________________

Pin Description (continued)

PIN

MAX1542

MAX1543

NAME

FUNCTION

14

14

IN

Supply Voltage. IN can range from 2.6V to 5.5V.

—

15

FREQ

Oscillator Frequency Select Input. Pull FREQ low or leave it unconnected for 640kHz
operation. Connect FREQ high for 1.2MHz operation. This input has a 5µA pulldown
current.

16

16

FB

Step-Up Converter Feedback Input. Regulates to 1.24V (nominal). Connect a resistor-
divider from the output (V

MAIN

) to FB to analog ground (AGND). Place the resistor-divider

within 5mm of FB.

17

17

COMP

Step-Up Regulator Error Amplifier Compensation Point. Connect a series RC from COMP
to AGND. See the Loop Compensation section for component selection guidelines.

18

18

DEL

High-Voltage Switch Delay Input. Connect a capacitor from DEL to AGND to set the high-
voltage switch startup delay. A 5µA current source charges C

DEL

.

For the MAX1542, the high-voltage switch between SRC and COM is disabled until V

DEL

exceeds 1.24V. Following the delay period, CTL controls the state of the high-voltage
switch.

For the MAX1543, the switches between SRC, COM, and DRN are disabled and a 1k

Ω

pulldown between COM and PGND is enabled until V

DEL

exceeds 1.24V. Following the

delay period, the 1k

Ω pulldown is released and CTL controls the state of the high-voltage

switches (see the Delay Control Circuit section).

19

19

CTL

High-Voltage Switch Control Input. When CTL is high, the high-voltage switch between
COM and SRC is on and the high-voltage switches between COM and DRN (MAX1543)
are off. When CTL is low, the high-voltage switch between COM and SRC is off and the
high-voltage switches between COM and DRN (MAX1543) are on. CTL is inhibited by the
undervoltage lockout and when V

DEL

is less than 1.24V.

—

20

DRN

Switch Input. Drain of the internal high-voltage back-to-back P-channel MOSFETs
connected to COM.

Typical Application Circuits

The MAX1542 typical application circuit (Figure 1) and
the MAX1543 typical application circuit (Figure 2) gen-
erate an +8V source driver supply and approximately
+22V and -7V gate driver supplies for TFT displays. The
input voltage is from +2.6V to +5.5V. Table 1 lists rec-
ommended components and Table 2 lists contact infor-
mation for component suppliers.

Detailed Description

The MAX1542/MAX1543 include a high-performance
step-up regulator, two high-current operational ampli-
fiers, and startup timing and level-shifting functionality
useful for active matrix TFT LCDs. Figure 3 shows the
MAX1542/MAX1543 functional diagram.

Main Step-Up Converter

The MAX1542/MAX1543 main step-up converter
switches at 1.2MHz or 640kHz (MAX1543 only) (see the
Oscillator Frequency (FREQ) section). The devices
employ a current-mode, fixed-frequency, pulse-width
modulation (PWM) architecture to maximize loop band-
width providing fast transient response to pulsed loads
found in source drivers for TFT LCD panels. The high-
switching frequency also allows the use of low-profile
inductors and capacitors to minimize the thickness of
LCD panel designs. The integrated high-efficiency
MOSFET and the IC’s built-in digital soft-start function
reduce the number of external components required
while controlling inrush current. The output voltage of
the main step-up converter (V

MAIN

) can be set from V

IN

to 13V with an external resistive voltage-divider at FB.

Advertising