Reset, Low-input-voltage, 300ma ldo regulators with, Applications information – Rainbow Electronics MAX1976 User Manual

Page 8: Chip information, Selector guide

Advertising
background image

MAX1963/MAX1976

The MAX1963/MAX1976 deliver up to 300mA and oper-
ate with an input voltage up to +3.6V. However, when
using the 6-pin SOT23 version, high output currents
can only be sustained when the input-output differential
voltage is less than 2V, as shown in Figure 2.

The maximum allowed power dissipation for the 6-pin
TDFN is 1.951W at T

A

= +70°C. Figure 3 shows that the

maximum input-output differential voltage is not limited
by the TDFN package power rating.

Applications Information

Capacitor Selection and

Regulator Stability

Capacitors are required at the MAX1963/MAX1976
input and output for stable operation over the full tem-
perature range and with load currents up to 300mA.
Connect a 1µF ceramic capacitor between IN and GND
and a 4.7µF low-ESR ceramic capacitor between OUT
and GND. The input capacitor (C

IN

) lowers the source

impedance of the input supply. Use larger output
capacitors to reduce noise and improve load-transient
response, stability, and power-supply rejection.

The output capacitor’s equivalent series resistance
(ESR) affects stability and output noise. Use output
capacitors with an ESR of 30m

Ω or less to ensure sta-

bility and optimize transient response. Surface-mount
ceramic capacitors have very low ESR and are com-
monly available in values up to 10µF. Connect C

IN

and

C

OUT

as close to the MAX1963/MAX1976 as possible

to minimize the impact of PC board trace inductance.

Noise, PSRR, and Transient Response

The MAX1963/MAX1976 are designed to operate with
low dropout voltages and low quiescent currents in bat-
tery-powered systems while still maintaining good
noise, transient response, and AC rejection. See the
Typical Operating Characteristics for a plot of Power-
Supply Rejection Ratio (PSRR) versus Frequency.
When operating from noisy sources, improved supply-
noise rejection and transient response can be achieved
by increasing the values of the input and output bypass
capacitors and through passive filtering techniques.

The MAX1963/MAX1976 load-transient response (see
the Typical Operating Characteristics) shows two com-
ponents of the output response: a near-zero DC shift
from the output impedance due to the load-current

change, and the transient response. A typical transient
response for a step change in the load current from 20mA
to 200mA is 20mV. Increasing the output capacitor’s value
and decreasing the ESR attenuates the overshoot.

Input-Output (Dropout) Voltage

A regulator’s minimum input-output voltage difference
(dropout voltage) determines the lowest usable supply
voltage. In battery-powered systems, this determines the
useful end-of-life battery voltage. Because the
MAX1963/MAX1976 use a P-channel MOSFET pass tran-
sistor, the dropout voltage is a function of drain-to-source
on-resistance (R

DS(ON)

= 0.33

Ω) multiplied by the load

current (see the Typical Operating Characteristics).

V

DROPOUT

= V

IN

- V

OUT

= 0.33

Ω

✕

I

OUT

The MAX1963/MAX1976 ground current reduces to 70µA
in dropout.

Low-Input-Voltage, 300mA LDO Regulators
with

RESET

in SOT and TDFN

8

_______________________________________________________________________________________

Chip Information

TRANSISTOR COUNT: 2556

PROCESS: BiCMOS

MAX1963

TOP MARK

MAX1976

TOP MARK

V

OUT

(V)

SUFFIX

SOT

TDFN

SOT

TDFN

0.75

075

AABA

AFQ

AAAQ

AGA

0.85

085

—

—

AABP

AHD

1.00

100

—

—

AABL

AGC

1.10

110

—

—

AABM

AGD

1.20

120

AABE

AFU

AAAK

AGE

1.30

130

AABF

AFV

AABN

AGF

1.50

150

AABG

AFW

AAAL

AGG

1.60

160

—

—

AABO

AHC

1.80

180

AABH

AFX

AAAM

AGH

2.50

250

AABI

AFY

AAAN

AGI

2.85

285

—

—

AAAO

AGJ

3.00

300

AABJ

AFZ

AAAP

AGK

Selector Guide

Advertising