Pin description, Detailed description – Rainbow Electronics MAX5090C User Manual

Page 7

Advertising
background image

MAX5090A/B/C

2A, 76V, High-Efficiency MAXPower Step-Down

DC-DC Converters

_______________________________________________________________________________________

7

Pin Description

PIN

NAME

FUNCTION

1, 2

LX

Source Connection of Internal High-Side Switch

3

BST

Boost Capacitor Connection. Connect a 0.22µF ceramic capacitor from BST to LX.

4

V

IN

Input Voltage. Bypass V

IN

to SGND with a low-ESR capacitor as close to the device as possible.

5

VD

Internal Regulator Output. Bypass VD to PGND with a 3.3µF/10V or greater ceramic capacitor.

6

SYNC

Synchronization Input. Connect SYNC to an external clock for synchronization. Connect to SGND to
select the internal 127kHz switching frequency.

7

SS

Soft-Start Capacitor Connection. Connect an external capacitor from SS to SGND to adjust the soft-
start time.

8

FB

Output Sense Feedback Connection.
For fixed output voltage (MAX5090A/MAX5090B), connect FB to V

OUT

.

For adjustable output voltage (MAX5090C), use an external resistive voltage-divider to set V

OUT

. V

FB

regulating set point is 1.228V.

9

ON/OFF

Shutdown Control Input. Pull ON/OFF low to put the device in shutdown mode. Drive ON/OFF high for
normal operation. Connect ON/OFF to V

IN

with short leads for always-on operation.

10

SGND

Signal Ground. SGND must be connected to PGND for proper operation.

11, 15, 16

N.C.

No Connection. Not internally connected.

12

PGND

Power Ground

13, 14

DRAIN

Internal High-Side Switch Drain Connection

—

EP

Exposed Pad. Solder EP to SGND plane to aid in heat dissipation. Do not use as the only electrical
ground connection.

Detailed Description

The MAX5090 step-down DC-DC converter operates
from a 6.5V to 76V input voltage range. A unique volt-
age-mode control scheme with voltage feed-forward
and an internal switching DMOS FET provides high effi-
ciency over a wide input voltage range. This pulse-
width-modulated converter operates at a fixed 127kHz
switching frequency or can be synchronized with an
external system clock frequency. The device also fea-
tures automatic pulse-skipping mode to provide high
efficiency at light loads. Under no load, the MAX5090
consumes only 310µA, and in shutdown mode, con-
sumes only 20µA. The MAX5090 also features under-
voltage-lockout, hiccup-mode output short-circuit
protection and thermal shutdown.

ON/

OFF

/Undervoltage Lockout (UVLO)

Use the ON/OFF function to program the external UVLO
threshold at the input. Connect a resistive voltage-
divider from V

IN

to SGND with the center node to

ON/OFF, as shown in Figure 1. Calculate the threshold
value by using the following formula:

Set the external V

UVLO(TH)

to greater than 6.45V. The

maximum recommended value for R2 is less than 1M

Ω.

ON/OFF is a logic input and can be safely driven to the
full V

IN

range. Connect ON/OFF to V

IN

for automatic

startup. Drive ON/OFF to ground to shut down the
MAX5090. Shutdown forces the internal power MOSFET
off, turns off all internal circuitry, and reduces the V

IN

supply current to 20µA (typ). The ON/OFF rising thresh-
old is 1.546V (max). Before any operation begins, the
voltage at ON/OFF must exceed 1.546V. The ON/OFF
input has 100mV hysteresis.

If the external UVLO threshold setting divider is not
used, an internal undervoltage-lockout feature monitors
the supply voltage at V

IN

and allows the operation to

start when V

IN

rises above 6.45V (max). The internal

UVLO rising threshold is set at 6.17V with 0.5V hystere-
sis. The V

IN

and V

ON/OFF

voltages must be above 6.5V

and 1.546V, respectively, for proper operation.

V

R

R

x

UVLO TH

(

)

.

=

+







1

1

2

1 38

Advertising