B&B Electronics ESR904 - Quick Start Guide User Manual
Quick start guide
Documentation Number ESP90x ESR90x-5012qsg
PN7071-rev001
1
2
3
4
5
6
7
8
Vlinx Serial Servers
Models: ESP901/902/904
ESR901/902/904
Model: ES1A
Quick Start Guide
LED
STATUS Function
Power
Red
Solid
Power apply
LINK
Yellow or
Green
Yellow
Green
Blinking
10BaseT
100BaseT
Network data activity
READY
Green
Blinking
Solid
Ready/normal
Bootup/reset/malfunction
Serial (if avail.)
Green
OFF
Solid
Blinking
Port not opened
Port opened
TX or TX/RX serial data activity
Serial (if avail.)
Red
OFF
Solid
Blinking
Port not opened
Port opened
RX serial data activity
□
Connect an Ethernet cable to the ESP/ESR unit if
connecting to a switch or crossover direct to the PC.
□
Connect the power supply to the ESP/ESR unit and
apply power.
□
ESP901/902/904 or ESR901/902/904 unit
□
Printed version of this ESP90x/ESR90x Quick Start Guide
□
CD ROM containing software and a comprehensive manual
□
Ext power supply (ESP901/902/904 ONLY)
□
ALOG100/ALOG110 module.
C
C
h
h
e
e
c
c
k
k
P
P
a
a
c
c
k
k
a
a
g
g
e
e
C
C
o
o
n
n
t
t
e
e
n
n
t
t
H
H
a
a
r
r
d
d
w
w
a
a
r
r
e
e
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
S
S
o
o
f
f
t
t
w
w
a
a
r
r
e
e
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
C
C
o
o
n
n
f
f
i
i
g
g
u
u
r
r
e
e
t
t
h
h
e
e
E
E
S
S
P
P
/
/
E
E
S
S
R
R
U
U
n
n
i
i
t
t
□
Click Start\Programs\B&B Electronics\Vlinx\ESP
Servers\Vlinx ESP Manager and it should auto-search for
attached ESP901/902/904 or ESR901/902/904 devices on
startup.
□
Note that the device must reside on the same subnet or
it won’t be seen by the Vlinx ESP Manager software for
first time discovery.
□
Use the Vlinx ESP Manager software to configure the
unit for network information, serial device configurations,
timeouts, etc (double-click on your device in the list).
□
Alternative method is to set the dipswitches in console
mode and use Hyperterminal set at 9600 and 8-N-1. Use
the arrow and <enter> key to configure (requires null
modem/cross-over serial cable connected to Port 1). Be
sure to set dipswitches back to run mode when done. (Not
avail. on ESP904).
□
Default password = <blank>
□
Reboot as necessary.
V
V
C
C
O
O
M
M
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
□
Click Start\Programs\B&B Electronics\Vlinx\Install Virtual COM
□
Search for all devices (must be in same subnet). Type specific
IP address otherwise.
□
Select your device from list (double click on your device).
□
Follow the onscreen instructions and install to a COM number
usually 5 or above to limit interference with existing real COM ports.
□
Use Hyperterminal to verify you can open your VCOM created.
S
S
e
e
r
r
i
i
a
a
l
l
D
D
e
e
v
v
i
i
c
c
e
e
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
L
L
E
E
D
D
S
S
t
t
a
a
t
t
u
u
s
s
Connect the serial device to the unit using the correct cabling:
□
Straight through serial cable for DCE serial device
□
Null modem (crossover) serial cable for DTE serial device
P
P
o
o
r
r
t
t
s
s
T
T
o
o
O
O
p
p
e
e
n
n
i
i
n
n
F
F
i
i
r
r
e
e
w
w
a
a
l
l
l
l
□
Insert the software CD and it should autostart into the
installation wizard.
□
Follow the on screen installation wizard to install the
Vlinx ESP Manager software.
Note: Be sure you have administrative rights & disable
firewalls Windows XP/Vista(see Section 8 also).
Model
Switch 1
Switch 2
Switch 3
ESP901
Run/console Run/console Run/console
ESP902
Run/console Run/console Run/console
ESP904
None
None
None
ESR901
Run/console TB or DB9
None
ESR902
Run/console None
None
ESR904
Run/console None
None
NOTE:
ESP01/902 must be ALL UP or ALL DOWN.
Ports
Function
5300
Heartbeat & configuration setting in TCP
mode (i.e. pair tunneling mode)
8888
Vlinx update
8889
Configuration setting in UDP mode
8890
Vlinx monitor
4000/1/2/3
VCOM
ESP901/902/904
ESR901/902/904