B&B Electronics 9000BP - Manual User Manual
B&B Electronics Accessories communication
Advertising
Table of contents
Document Outline
- Industrial Gigabit Ethernet Switch Installation Guide
- Safety Warnings
- INSTALLATION
- SERVICING
- CAT5 CABLE SPECIFICATIONS
- CONNECTING THE UNIT
- Overview of Advanced Features
- Web Software Configuration
- Web Management - Home
- Ports – Security
- Ports – Intrusion Log
- Ports – Mirroring
- Ports – Trunking
- Statistics – Port Statistics
- VLAN – Ingress Filter
- VLAN – Port Based
- Bridging – Aging Time
- Bridging – Unicast Addresses
- Bridging – Multicast Addresses
- RSTP – RSTP Configuration
- IGMP – Configuration
- IGMP – Show Group and Show Router
- IGMP – RFilter
- N-Ring – Configuration
- N-Ring – Status
- NView – Configuration
- NView – Ports
- EventLog – Log Statistics
- EventLog – Show Events
- Firmware/Config – TFTP
- Firmware/Config – FTP
- Support – Web Site and E-mail
- BPCL – Broadcast Packet Count Limit Configuration
- User Mgmt – Adding Users
- User Mgmt – Removing Users
- Logical View
- Configuration – Save or Reset
- Help – Overview
- Help – Administration
- Help – Ports
- Help – Statistics
- Help – VLAN
- Help – BPCL
- Help – IGMP
- Help – Bridging
- Help – RSTP
- Help – Event Log
- Help – Firmware/Config
- Help – Logical View
- Help – User Mgmt
- Help – N-View
- Help – N-Ring
- Help – Others
- CLI Commands
- System Configuration Commands
- Set Mode IP config
- Set IP/Subnet/Gateway Addresses of the system
- Get IP Address of the system
- Set System Name
- Get System Name
- Get Gateway Address of the System
- Get Mac Address of the System
- Get Netmask of the System
- Get System Contact
- Set System Contact
- Get System Location
- Set System Location
- Get System Uptime
- Get Number of Ports present in the System
- Set IP Address of an SNMP Management Stations
- Set SNMP Get Community name
- Set SNMP Set Community name
- Set SNMP Trap Community name
- Show all configuration parameters
- Show all configuration parameters related to SNMP manager
- System Restart
- User Management Commands
- TFTP Commands
- FTP Commands
- Port Manager Commands
- Get the link state of a given port
- Get admin status of the port
- Set admin status of a port
- Show port statistics
- Get total number of good frames received
- Get port speed
- Set Port Speed
- Get the port duplex mode
- Set the port duplex mode
- Set the Lockstate of a given port
- Get Lock State
- Get Auto-negotiation State
- Set Auto-negotiation State
- Set Priority State
- Set Flow Control
- Set Name
- Set PVID
- Set Backpressure
- Set Intruderstate
- Set Priority Level
- Show Configuration
- Show Intruders
- Show Link Utilization
- Get Flow Control
- Get Name
- Get State Of Priority
- Get Intruder State
- Get Priority Level
- Get STP Status
- Get Back Pressure
- Get PVID
- Clear Counters
- Clear Intruder Log
- Trunk related commands
- Mirroring related commands
- VLAN Related Commands
- Eventlog Related Commands
- Bridging Related Commands
- IGMP Related Commands
- N-Ring Related Commands
- Configuration Related Commands
- Rapid Spanning Tree Protocol Related Commands
- Set RSTP Admin Edge
- Get RSTP Admin Edge
- Set RSTP Auto Edge
- Get RSTP Auto Edge
- Set RSTP Bridge Admin Status
- Get RSTP Bridge Admin Status
- Set RSTP Bridge Forward Delay
- Get RSTP Bridge Forward Delay
- Set RSTP Bridge Hello Time
- Get RSTP Bridge Hello Time
- Set RSTP Bridge Max Age
- Get RSTP Bridge Max Age
- Set RSTP Bridge Priority
- Get RSTP Bridge Priority
- Set RSTP Port Path Cost
- Get RSTP Port Path Cost
- Set RSTP Port Priority
- Get RSTP Port Priority
- Broadcast Packet Count Limit Commands
- VLAN Configuration Examples
- Example 1 – Basic understanding of port based VLANs
- Example 2 – Basic understanding of tagged VLANs (Admit – Tagged Only)
- Example 3 – Basic understanding of tagged VLANs (Admit – All)
- Example 4 – Basic understanding of Hybrid VLANs
- Example 5 – Basic understanding of Overlapping VLANs
- Example 6 – Basic understanding of VLANs with Multicast Filtering
- KEY SPECIFICATIONS
- N-TRON Limited Warranty