Dual Electronics MXDM66 - Manual (Page 4)

7 6
Press and hold AUDIO/MENU for more than 3 seconds to
access the setup menu, then press AUDIO/MENU to cycle
through menu options. When desired option appears in the
display, rotate the rotary encoder left/right to adjust or activate
the desired function. Press ESC to exit the menu at any time.
Setup Menu
MXDM66 OPERATION
General Operation
Setup Menu
Menu Function Options Action
Auto Station
Store
AUTO STORE
Press SELECT to seek and save 6 strong stations in the current band.
Note: This option only appears in Tuner mode.
Loudness
Curve
LOUD OFF Disables the loudness function.
LOUD ON
Enables the loudness function. Activating this feature will enhance the
bass and treble frequencies when listening to music at low volumes.
Tuner Frequency
Spacing
FREQ USA
Programs unit to USA tuner spacing.
(200kHz for FM and 10kHz for AM)
FREQ EUR
Programs unit to European tuner spacing.
(50kHz for FM and 9kHz for AM)
Clock
Display
CLK OFF Programs unit to not display the clock when the power is off.
CLK ON Programs unit to display the clock when the power is off.
Auxiliary
Input
AUX ON Enables the front panel 3.5mm auxiliary input.
AUX OFF Disables the auxiliary input.
Beep Confirmation
BEEP OFF Disables the confirmation beep.
BEEP ON Enables the confirmation beep.
Programmable
Turn On Volume
PRO-VOL #
Programs unit to turn on at a specific volume
(default is OFF).
Local/Distance
Tuning
LOCAL OFF Activates distance tuning.
LOCAL ON Activates local tuning for strong station reception only.
Power on Message
MSG OFF Disables power on message.
MSG ON Enables power on message to be displayed.
Scrolling
Option
SCROLL ONCE
Programs unit to scroll once, then show the first 10 characters on the
display.
SCROLL ON Programs unit to scroll continuously.
SCROLL OFF Programs unit to show the first 10 characters on the display.
Illumination
Dimmer
DIMMER HI Programs unit to the brightest illumination level.
DIMMER MED Programs unit to the middle illumination level.
DIMMER LOW Programs unit to the dimmest illumination level.
Demonstration
Mode
DEMO OFF Disables the demonstration mode.
DEMO ON Enables the "FULL SPEED USB INPUT " message.
Faceplate Removal
Semi-Permanent
Faceplate Installation
Power On/Off
Mode
Auxiliary Input
Volume
Mute
Preset EQ Curves
Reset
Display
Set the Clock
12/24-hour Clock
General Operation
MXDM66 OPERATION
Press RELEASE and pull away from the left side to remove.
To re-install, insert right side of faceplate first then push
left side to secure.
Remove trim ring and install supplied #1 x 7/32” Phillips
head screw through left side of mounting frame into faceplate.
Press or any other button (except eject) to turn the unit
on. Inserting a disc will turn the unit on automatically. Press
and hold to turn the unit off.
Press MODE to select between AM/FM, CD player, auxiliary
input and USB. Modes of operation are indicated in the
display.
Note: CD mode will not appear unless a CD is inserted.
Insert 3.5 mm plug to connect your portable audio device.
Adjust volume using rotary encoder (00-46).
Press MUTE to silence the audio. “MUTE” will flash in the
display. Press MUTE again to cancel.
Press EQ to enter EQ setup menu, then use the rotary
encoder to select between POP, JAZZ, CLASSIC, BEAT, ROCK
and FLAT (default) equalization curves. Any adjustment to
the Bass or Treble settings automatically cancels the current
EQ curve (if one is selected).
Press to RESET the unit upon initial installation or if
abnormal operation occurs. The reset button is located
behind the faceplate.
Press DISP to select between clock and different types of
information, such as radio frequency, CD track or MP3/USB
song information.
With the unit on, press and hold DISP until the clock begins
to flash, then release. Press TUNE nn to adjust the
hours and TUNE ll to adjust the minutes. Press DISP
momentarily to save the selected time.
The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10:00). In European frequency spacing
mode, the clock will display 24-hour time (22:00).