Asus P5GD2-X - Manual (Page 40)

1 - 2 8 1 - 2 8 1 - 2 8 1 - 2 8 1 - 2 8 C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n
2 . 2 . 2 . 2 . 2 . P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E )
These connectors are for Ultra DMA 100/66 signal cables. The Ultra
DMA 100/66 signal cable has three connectors: a blue connector for
the primary IDE connector on the motherboard, a black connector for
an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive),
and a gray connector for an Ultra DMA 100/66 IDE master device (hard
disk drive). If you install two hard disk drives, you must configure the
second drive as a slave device by setting its jumper accordingly. Refer
to the hard disk documentation for the jumper settings.
• Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
• Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
P5GD2-X
®
P5GD2-X IDE connector
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
PRI_IDE
3 . 3 . 3 . 3 . 3 . S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s
( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 )
( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 ) ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 ) ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 ) ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
Install the Windows ® 2000 Service Pack 4 or the Windows ® XP Service
Pack1 or later before using Serial ATA.
P5GD2-X
®
P5GD2-X SATA connectors
SATA2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
SATA4
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXP4
RSATA_RXN4
GND
SATA3
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND