Extron Electronics MTP_HDMI U R Setup Guide User Manual
Mtp/hdmi u r • setup guide, Installation, Step 1 — mounting
IMPO
RTAN
T:
Go to www
.extron.com f
or the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
MTP/HDMI U R • Setup Guide
The Extron
®
MTP/HDMI U R is a twisted pair and HDMI universal receiver for analog and
DIGITAL OUTPUT
DIGITAL INPUT
POWER
12V
0.8A MAX
1
2
HDMI
RS-232
PASS THRU
Tx Rx
RGB
VID
Y/C
B-Y
Y
R-Y
ANALOG OUTPUTS
RS-232
Tx Rx
SPARE
MTP INPUT
1
MONO AUDIO
2
MTP/HDMI U R
RGB
PEAKING
LEVEL
DIGITAL SIGNAL
ANALOG
SIGNAL
AUDIO
RS-232
VID
Y/C
YUV
RGB
digital signals, and is compatible with MTP and HDMI 201 Tx transmitters.
For full details, see the MTP/HDMI U R User Guide
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the device as required.
Step 2 — Connect Input
Connect up to two twisted pair cables from an HDMI 201 Tx to the RJ-45 connectors labeled Digital Inputs 1 and 2. Connect an MTP transmitter,
a switcher, or a Distribution Amplifier (DA) to the MTP input.
ATTENTION:
Do not connect the twisted pair input cables to a LAN port, or connect a LAN cable to the digital or MTP ports.
Step 3 — Connect Outputs and RS-232 Control Devices
•
Analog video— Connect output devices to the
RGB
VID
Y/C
B-Y
Y
R-Y
ANALOG OUTPUTS
RS-232
Tx Rx
SPARE
1
MONO AUDIO
2
Component Video –
Connect to these 3 BNCs.
Composite Video –
Connect to this BNC.
RGBHV and RGBS –
Connect to this VGA
connector.
S-video – Connect to
this mini DIN connector.
Mono Audio – Connect
to this captive screw
connector.
Wire the RS-232 connector as shown below.
L
MONO AUDIO
R
L
MONO AUDIO
R
Unbalanced Output
Balanced Output
Mono output 1-
Sleeve(s)
Mono output 1+
Mono output 2+
Mono output 2-
Sleeve(s)
Mono output 1
Mono output 2
NO GROUND.
NO GROUND.
Ground
Tx
Rx
Gnd
Receive
Transmit
Connected RS-232 Device Pins MTP/HDMI U R
Pins
Spare
Spare
Wire the audio connector as shown above.
RS-232 Control (Analog Side) –
Connect to this captive screw
connector.
Do not tin
the wires!
Analog Output connectors (see image to the right).
NOTE: The analog outputs are the signals generated
on the MTP input. The signal is sent to the
appropriate detected analog output.
•
Audio — Connect a suitable audio device to the 5-pole
captive screw audio output connector for a balanced or
unbalanced, dual mono audio signal. Wire connector as
shown in the figure at right.
NOTE: The audio signal is detected from the MTP input,
and then is distributed to the audio connector for
output. Audio from the digital side is not available.
•
Control device (analog side) — Connect a serial communications port to the upper 3.5 mm, 5-pole captive screw
connector for bidirectional or unidirectional RS-232 communication. Wire the connector as shown in the figure above
NOTE: The RS-232 port configuration (analog side) as unidirectional or bidirectional is controlled by the internal
jumper settings (see
•
Digital video — Connect a suitable output to the female HDMI output.
Control device (digital side) — Connect a serial communications port to the 3.5 mm, 3-pole
captive screw connector for pass-through RS-232 bidirectional communication. Wire the
connector as shown on the right. .
Step 4 — Connect Power
Wire a standard IEC power cord from a 100 to 240 VAC, 50 - 60 Hz power source into the 12 VDC,
0.8 A, 2-pole captive screw connector (see image
a
on the right). When power is applied the
front panel power LED lights.
Grounding guidelines
Extron MTP/HDMI U R products can be adversely affected by electrostatic discharge (ESD) if
they are not grounded correctly.
To prevent malfunctions or product damage, an experienced installer can correctly ground an
Extron MTP/HDMI U R in either of two ways:
•
Ground the power input port — Insert one end of the grounding wire to the negative or ground
pin on the power input connector (see image
a
on the right). Tie the other end of the wire to an
earth ground.
•
Ground the chassis — Use a connector hex nut as shown in image
b
the right. Tie the other
end of the wire to an earth ground.
If you have any questions about how to ground a product in a specific application, contact an Extron
technical support specialist.
Connected RS-232
Device Pins
MTP/HDMI
RS-232
Pass-thru
Tx Rx
Rx Tx Grnd
a
Power Supply
Output Cord
SECTION A–A
Ridges
Smooth
A
A
POWER
12V
xA MAX
Tie
Wrap
Rear
Panel
Ridges
Earth
Ground
3/16"
(5 mm)
Max.
b