Document Outline

• PoleVault Digital Switcher Systems
  • Conventions Used in this Guide
    • Notifications
    • Software Commands
      • Specifications Availability
• Contents
• Introduction
  • Overview
  • The Digital PoleVault, WallVault, and PlenumVault Systems
    • Application Diagram
    • Before You Begin — Planning the Installation
      • Americans with Disabilities Act (ADA) Compliance
      • Room Layout
    • Inventory — PoleVault Digital System
      • Kits
    • Inventory — WallVault Systems (USFM 100)
      • 42-209-03 WVS 200D
      • 42-210-03 WVS 400D
    • Inventory — WallVault Systems (WMK 160)
      • 42-211-03 WVS 210D
      • 42-212-03 WVS 410D
    • Inventory — PlenumVault Systems (PVM 220)
      • 42-220-03 PLS 200D
      • 42-221-03 PLS 400D
      • 42-230-03 PLS 210D
      • 42-231-03 PLS 410D
    • Items Not Included
    • Installation Tools
    • Optional Items
• Installation
  • Overview
  • Outline of Installation Steps for PoleVault Digital Systems
  • Stage 1: Installing the Screen and Projector
    • 1. Mark Screen Location
      • 2. Install Projector to Verify Location
      • 3. Verify the Image Location
      • 4. Cut the Ceiling Tile
      • 5. Preliminary Safety Hardware Installation
      • 6. Finish Projector Drop Ceiling Mount Installation
      • 7. Secure the Projector Drop Ceiling Mount to the Ceiling
      • 8. Install the Electrical Box (if required)
      • 9. Install the Screen
  • Stage 2: Mounting the PVT Wallplate and the MediaLink Controller
    • 1. Install the Mud Rings
      • 2. Pull the Cables (at the input locations)
      • 3. Install Wall Plates
      • 4. Install MediaLink Controller
  • Stage 3: Installing the FF 120 Ceiling Speakers
    • 1. Cut Ceiling Tile
      • 2. Install the Speaker on the Drop Ceiling
      • 3. Terminate the Speaker Cable for the PVS Switcher
  • Stage 4: Installing the Switcher Mounting System and the PVS 405D
  • A. PoleVault System (PMK 560 Pole Mount Kit)
    • A1. Install the PMK 560 Base Plate
      • A2. Pull the Cables (at the Switcher location)
      • A3. Secure the HDMI cables using the LockIt bracket
      • A4. Finish installing the Mounting Kit
      • B1. Install the WMK 160 Base Plate
  • B. WallVault System (WMK 160 Wall Mount Kit)
    • B2. Install the switcher onto the Base Plate
      • B3. Run the cables to the WMK 160 location
      • B4. Cable the switcher
      • B5. Final Installation
  • C. WallVault System (USFM 100 Short Throw Wall Mount Kit)
    • C1. Install the USFM 100 Base Plate
    • For drywall with wood studs
    • For drywall with steel studs
      • C2. Install the switcher onto the Base Plate
      • C3. Run the cables to the USFM 100 location
    • If running cable behind the walls:
    • If using a surface raceway or conduit:
      • C4. Cable the switcher
      • C5. Attach the Boom Arm, Power Supply, and Projector
  • D. PlenumVault System (PVM 220 PlenumVault Mount Kit)
    • D1. Remove the device mounting plate from the access door
      • D2. Remove ceiling tile and install suspension cables.
      • D3. Suspend the main PVM 220 enclosure from the ceiling.
      • D4. Run AC power wiring to the AC module in the PVM 220
      • D5. Run signal and control cables to the PVM 220.
      • D6. Install devices onto the device mounting plate.
      • D7. Cut and install the ceiling tile in the access door.
      • D8. Install the device mounting plate onto the access door.
      • D9. Cable the switcher
      • D10. Verify and configure the setup.
      • D11. Attach the door tether to the door.
      • D12. Secure the door latches.
  • Stage 5: Configuring the PVS 405D Switcher
    • 1. Configure the Switcher — PCS Product Configuration Software Program
      • 2. Configure the System — Global Configurator
      • 3. Test the System
      • 4. Final Installation
  • Optional Accessory Installation — VoiceLift System
    • VoiceLift System Included parts:
      • Installation Procedure
  • Optional Accessory Installation — Priority Page Sensor (PPS 35)
    • Installation Procedure
  • Optional Accessory Installation — Priority Page Sensor Kit (PPS 25)
    • Priority Page Sensor Kit Included Parts:
      • Installation Procedure
      • Testing and Adjustment Procedure
• Installation Outlines
  • Outline of Installation Steps for WallVault Digital Systems (WMK 160)
  • Outline of Installation Steps for WallVault Digital Systems (USFM 100)
  • Outline of Installation Steps for PlenumVault Digital Systems (PVM 220)
  • Outline of Installation Steps for PoleVault Digital Systems
• Extron Warranty