Braun EP60 Exact Power - Manual (Page 4)

Description
1 Distancing comb 4 On/off switch
2 Pivoting twin cutter system with beard length selector
a beard trimmer 5 Memory switch
b contour trimmer (for 6 beard length settings)
c release buttons 6 Pilot light
3 Speed selector
Technical specifications
Power supply: 100 – 240 V 2 / 50 or 60 Hz (automatic adaptation)
Wattage: 1.35
Charging your beard trimmer for cordless operation
• For the first 3 chargings: Plug in trimmer with the on/off switch on position «0»
and charge it for at least 20 hours. The pilot light indicates that the trimmer is
charging.
• Once the trimmer is completely charged, use it without the cord until discharged.
• Then recharge to full capacity again (subsequent charges will take about
16 hours).
• A full charge will give up to 30 minutes of cordless trimming depending on
your beard. However, the maximum capacity will only be reached after several
charging/discharging cycles.
• Best environmental temperature range for charging is 60 °F to 95 °F / 15 °C to 35 °C.
Using your beard trimmer
Speed selector
1 Normal setting for beard and contour trimming
2 High speed setting for strong beard and difficult areas (e.g. chin)
Beard trimming (A)
• Place the distancing comb on the beard trimmer while the on/off switch is on
position «0».
• To start trimming, press the on/off switch and push it up to the desired beard
length. You may choose between 6 settings: approx. 1, 3, 6, 9, 12, 16 mm.
• It is advisable to begin with the highest setting and then reduce the setting until
you reach the desired beard length.
• Hold the distancing comb with the angled edge against your beard and guide
the trimmer against the direction of hair growth.
• As you become familiar with beard length settings, you may want to adjust the
memory switch to your preferred beard length setting by sliding it up. With the
preset memory switch, the motor will not start before the on/off switch has
reached the memory switch setting.
• To avoid clogging the distancing comb with hair, clean it from time to time with
the brush. Please note that the distancing comb can only be taken off, when the
trimmer is turned off.
Contour trimming (B)
• The contour trimmer is ideal for precisely outlining beard contours, for shaping
partial beards and also for removing long single hairs.
• To use the contour trimmer, take off the distancing comb. Tip (tilt) the twin
cutter system so that the narrow contour cutter locks in the upper position.
Keeping your trimmer in top shape
Cleaning and care (C)
• After each use, take off the distancing comb and slightly shake or brush hair
from the beard trimmer and the distancing comb.
• Press the release buttons to lift off the twin cutter system. Using the brush,
clean the twin cutter system and the inside of the trimmer.
• To keep the twin cutter system working properly, we recommend that you oil
the cutting system regularly with light machine oil.
• Then click the twin cutter system back to original position by pushing forward.
Preserving the rechargeable battery
In order to maintain the capacity and life of the rechargeable battery, the trimmer
has to be discharged by regular use approximately every 6 months. Then
recharge to full capacity again. Do not keep the trimmer on permanent charge.
Environmental notice
This appliance is provided with a nickel-hydride rechargeable battery
which does not contain any harmful heavy metals. Nevertheless,
in the interest of recycling raw materials, please do not dispose of
the appliance in the household waste at the end of its useful life.
Disposal can take place at a Braun Service Center or at appropriate
collection sites.
Subject to change without notice.
᧙
5601113_EP60_NA Seite 4 Donnerstag, 29. Januar 2004 2:16 14