Cla-Val 60-32/660-32 - Manual (Page 4)

CLA-VAL
Copyright Cla-Val 2013 Printed in USA Specifications subject to change without notice.
P.O. Box 1325 • Newport Beach, CA 92659-0325 • Phone: 949-722-4800 • Fax: 949-548-5441 • E-mail: [email protected] • Website cla-val.com
©
Auto
Off
Hand
L1 SW1
A 3CR3
L2
1CR
H
1CR
1CR
3CR1
N.C. 2CR
PVS
2CR
3CR
M
COM.
SW
2 N.O.
3CR
2 2CR
Auto-Off-Hand = Selector Switch
1CR = Relay, DPST Normally Open
2CR = Relay, DPST Normally Open
3CR = Relay, TPST Normally Open
SW1 = Switch, Remote Start/ Stop
SW2 = Switch, SPDT, Valve Limit Switch
PVS = Pilot Valve Solenoid
M = Pump Motor Starter
Note: SW2 and PVS supplied by Cla-Val
Co. All other electrical items supplied by
customer. SW2 is included in the X105L
switch assembly which is mounted on the
pump control valve cover.
Shown In Pump Off Position
Optional Model PC-1 Pump Control
Panel has flexible control settings for
maximum electrical interlock control. It is
pre-wired and ready for easy field hook-
up wiring. See E-PC-1 data sheet.
Pilot System Specifications
Adjustment Ranges
0 to 75 psi
20 to 105 psi
20 to 200 psi*
100 to 300 psi
*Supplied unless otherwise specified
Other ranges available, please consult factory
Temperature Range Water: to 180°F Max
Materials
Standard Pilot System Materials
Pilot Control:
Bronze ASTM B62
Trim: Stainless Steel Type 303
Rubber: Buna-N ® Synthetic Rubber
Optional Pilot System Materials
Pilot Systems are available with optional
Stainless Steel or Monel materials
Solenoid Contro l
Body:
Brass ASTM B283
Enclosure:
General Purpose, Watertight 1,2,3,3S,4,4X
Optional: Class I, Division 2, Hazardous Locations
and Watertight Type 3, 3S, 4, 4X
Voltages:
100-240V / 50-60 Hz AC or DC
24-99V / 50-60Hz AC or DC
2-24VDC
Manual Operator Standard
Max. operating pressure differential: 350 psi
Coil:
Insulation molded Class F
Watts AC 2
When Ordering,
Please Specify
1. Catalog No. 60-32 or
No. 660-32
2. Valve Size
3. Pattern - Globe or Angle
4. Pressure Class (Flanged)
5. Trim Material
6. Electrical Selection
7. Desired Options
8. When Vertically Installed
(Flow Direction)
Note: For optimum operation of built-in check feature, installation with valve stem vertically position is recommended.
E-60-32/660-32 (R-1/2013)
60-32
Valve
Selection
100-04 Pattern: Globe (G), Angle (A), End Connections: Threaded (T), Flanged (F) Indicate Available Sizes
Inches 4 6 8 10 12 14 16
mm 100 150 200 250 300 350 400
Basic Valve
100-04
Pattern G, A G, A G, A G, A G, A G, A G, A
End Detail F F F F F F F
Suggested
Flow
(gpm)
Maximum 800 1800 3100 4900 7000 8400 11000
Maximum
Intermittent
990 2250 3900 6150 8720 10540 13700
Suggested
Flow
(Liters/Sec)
Maximum 50 113 195 309 442 530 694
Maximum
Intermittent
62 142 246 387 549 664 863
100-04 Series is the full internal port Hycheck.
660-32
Valve
Selection
100-23 Pattern: Globe (G), Angle (A), End Connections: Flanged (F) Indicate Available Sizes
Inches 4 6 8 10 12 14 16 18 20 24
mm 100 150 200 250 300 350 400 450 500 600
Basic Valve
100-23
Pattern G, A G, A G, A G G G G G G G
End Detail F F F F F F F F F F
Suggested
Flow
(gpm)
Maximum 580 1025 2300 4100 6400 9230 9230 16500 16500 16500
Suggested
Flow
(Liters/Sec)
Maximum 37 65 145 258 403 581 581 1040 1040 1040
100-23 Series is the reduced internal port size version of the 100-04 Series.
Wiring Diagram