Atec Tinius-Olsen-H1KS - Manual (Page 3)

3
Key Features
• PC control via high speed
• RS232 using ASCII mode and super
high speed binary mode
• Machines are proof loaded to 200%
of capacity
• Force accuracy of 0.5% of applied
load across the load cell display
range
• Built-in intelligent active force and
displacement alarm system
• 32 bit precision motor controller
• Displacement resolution of 0.0001
mm (T series in binary mode)
• Speed resolution of 0.001 mm/min
• 150% mechanical overload capacity
on each load cell
• 20% digital load tare while
maintaining full load cell capacity
• Automatic motor drive alarms that
monitor over/under voltage, current
and temperature
Specifications:
Load measurement accuracy: +/- 0.5% of applied load from 2% to 100%
capacity; extended range down to 1% capacity with accuracy of 1% of
applied load
Position measurement accuracy: +/- 0.01% of reading or 0.001 mm,
whichever is greater
Speed accuracy: +/- 0.005% of set speed
Operating temperature range: 32 to 100 degrees F (0 to 38 degrees C)
Storage temperature range: 14 to 115 degrees F (-10 to 45 degrees C)
Humidity range: 10% to 90% non-condensing, wet bulb method
Power: standard optional voltages 220/240VAC, 50-60 Hz, 2000W; power
must be free of spikes and surges exceeding 10% of the nominal voltage
Notes: 1. Load weighing system meets or exceeds the requirements of the following standards: ASTM E4, EN
10002-2, BS 1610, DIN 51221, ISO 7500-1. Tinius Olsen recommends that systems are verified at installation
in accordance with ASTM E4 and ISO 75001. 2. Strain measurement system meets or exceeds the require-
ments of the following standards: ASTM E83, EN 10002-4, BS 3846 and ISO 9513. 3. These models conform
to all relevant European CE
Health and Safety Directives EN
50081-1, 580081-1, 73/23/EEC,
EN 61010-1 4. Specifications
are subject to change without
notice
Fig 9. A model H5kT
and a model H5kS being
used to determine the
bonding strength of
adhesive tape
Fig 6. Testing of rigid plastics and use of
Model 100R multi gauge length extensometer
Fig 7. Model
H5kT being
used to
determine
the flexural
strength of
a printed
circuit board
Fig 8. Model H1kS
being used to find
the tensile strength
of a baby’s pacifier
Technical Specifications
lbf 200 1000
kN 1 5
kg 100 500
in 6 8
mm 150 200
in 17.5 30
mm 445 750
in/min
mm/min
in/min 0.00004 to 40 0.00004 to 40
mm/min 0.001 to 1000 0.001 to 1000
in/min 0.00004 to 40 0.00004 to 60
mm/min 0.001 to 1000 0.001 to 1500
in 32 x 14 x 14 45 x 19 x 18
mm 820 x 360 x 360 1140 x 490 x 450
lb 55 110
kg 25 50
MAXIMUM SAMPLE
DIAMETER
LOAD
CELLS
MAXIMUM
CROSSHEAD
TRAVEL
(EXCLUDING GRIPS)
TESTING SPEED
RANGE
JOG SPEED
RETURN SPEED
DIMENSIONS
H x W x D
CAPACITY
MODEL H1k H5k
WEIGHT
Rapid change, Z beam load cells
with digital encoding for
automatic recognition and
scaling available — 1kN, 500N,
250N, 100N, 50N, 10N, 5N
Rapid change, Z beam load cells
with digital encoding for automatic
recognition and scaling available
— 5kN, 2.5kN, 1kN, 500N, 250N,
100N, 50N, 10N, 5N
Measurement direct from ballscrew
— fully auto scaling of single
measurement range
Measurement direct from ballscrew
— fully auto scaling of single
measurement range
0.001 to 1000 up to 500N
0.001 to 500 up to 1kN
0.00004 to 60 up to 200 lbf,
0.00004 to 20 up to 1000 lbf
0.001 to 1500 up to 1kN
0.001 to 500 up to 5kN
0.00004 to 40 up to 100 lbf,
0.00004 to 20 up to 200 lbf