BVA Hydraulics P8701, P8701M - Manual (Page 8)

LIFETIME LIMITED WARRANTY
BVA Hydraulics®, represented in the United States by Shinn Fu Company of America, Inc. [“SFA”] warrants this product
to be free from defects in material and workmanship for the life of the product as long as the original purchaser owns the
product. The warranty is non-transferable and is subject to the terms, exclusions, and limitations described below:
• Damaged components, including but not limited to bent rams, dented or crushed cylinder walls, broken welds or couplers
as well as worn out seals, o-rings and springs are the result of misuse and not covered by warranty and BVA Hydraulics
will not provide any warranty credit for such damaged components.
• This warranty does not cover ordinary wear and tear, overloading, alterations (including repairs or attempted repairs not
performed by BVA Hydraulics or one of its authorized personnel), improper fluid use, or use of the product in any manner
for which the product was not intended or the use of which is not in accordance with the instructions or warnings provided
with the product.
• In the unlikely event that a BVA Hydraulics product fails due to material defect in workmanship, you may contact SFA
for disposition. In such cases, the customer’s sole and exclusive remedy for any breach or alleged breach of warranty is
limited to the repair or replacement of the defective product.
• Under no circumstances is BVA Hydraulics liable for any consequential or incidental damage or loss whatsoever.
• THIS WARRANTY IS LIMITED TO NEW PRODUCTS SOLD THROUGH AUTHORIZED DISTRIBUTORS AND OTHER
CHANNELS DESIGNATED BY BVA HYDRAULICS. NO AGENT, EMPLOYEE OR OTHER REPRESENTATIVE OF BVA
HYDRAULICS IS AUTHORIZED TO MODIFY THIS WARRANTY.
• THE FOREGOING IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FOR A FITNESS FOR
A PARTICULAR PURPOSE.
• Components not manufactured by BVA Hydraulics including certain motor systems, gasoline engines, and others are not
covered by this warranty and instead are covered by the manufacturer’s separate manufacturer’s warranty provided in
the package.
• BVA Hydraulics’ liability in all cases is limited to, and will not exceed the purchase price paid for the product.
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
Tel: 888-332-6419
E-mail: [email protected]
TROUBLESHOOTING GUIDE
The following information is intended as an aid in determining if problem exists. Pumps should be repaired only by authorized
BVA Service Center. For repair service, contact service center in your area.
Symptom Possible Causes Corrective Action
Erratic application action • Air in the system
• External leak
• Internal hydraulic leak
• Vent the system
• Tighten all connections
• Contact service center
Application does not extend, move
or respond to pressurized fluid
• Overload condition
• Release valve not closed
• Loose couplers
• Faulty couplers
• Pump malfunction
• Remedy overload condition
• Ensure release valve closed
• Tighten couplers
• Replace couplers
• Contact service center
Application responds to pressurized
fluid, but system does not maintain
pressure
• Overload condition
• Release valve not closed
• Pump or valve malfunction
• Application/connection leaking
• Remedy overload condition
• Ensure release valve closed
• Contact Service Center
• Replace application/connection
Application responds slower than
normal
• Loose connection or coupler
• Restricted hydraulic line or fitting
• Application/connection leaking
• Tighten connection or coupler
• Clean and replace if damaged
• Replace application/connection
Application does not return fluid to
pump (i.e. cylinder will not retract)
• Malfunctioning coupler, damaged
application
• Reservoir overfilled
• Secure load by other means. Depressurize
pump and hose, remove coupler and/or
application, then renew or replace
• Secure load by other means. Depressurize
pump and hose, remove application, then
drain fluid to proper level
Application does not fully extend
(cylinder or spreader)
• Fluid level in pump is low
• Volume of oil is not sufficient to
extend application
• Secure load by other means. Depressurize
pump and hose, remove application, then
fill fluid to proper level
• Secure load as above, then match pump to
application.
Poor performance • Fluid level in pump is low • Ensure proper fluid level
8