Hunter 27181 Four-Speed Slide Wall Control - Manual

Installation Instructions:
1. Set the ceiling fan’s speed to the HIGH position
before installing this control. Do not change the ceil-
ing fan‘s speed setting after your speed control is
installed, as damage to your ceiling fan or All-Fan™
control may result.
2. Verify proper operation of the ceiling fan wall
switch before installation. Improper wiring can
damage the control, and will void the warranty.
3. Disconnect power to ceiling fan at the main electric
panel. Remove fuse or switch circuit breaker to OFF
position.
4. Refer to the Installation Figure for your All-Fan™
speed control. Remove wallplate to expose the wiring,
and disconnect the existing switch.
Install in a metal or plastic wallbox.
5. If 4 wall wires are visible, connect
each black wire lead to the All-Fan™
speed control’s black wire. If 2 wires
are visible, connect each to an All-Fan™
speed control lead. Use the wire nuts
supplied to make the connections.
Refer to the Wiring Diagram, which
shows the proper connections.
If a ground wire is provided in your
electrical box, attach it to the ground
screw near the bottom of the mount-
ing plate.
6. Gently push wires and speed con-
trol into switch box. Attach the All-Fan™
speed control to switch box with the
two screws supplied.
7. Mount wallplate over control with
existing screws.
8. Move slider to the OFF position.
9. Restore power at main electrical
panel.
10. Operate ceiling fan moving slider to the desired
speed.
For best operation: select HIGH speed until
motor starts, then select desired speed.
Form 41312 (6/98)
Control deslizable para ventilador de 4
velocidades
Lea y guarde estas instrucciones
Cuidado:
! Riesgo de choque eléctrico
Todo el cableado y conexiones se deben hacer
de acuerdo con los códigos eléctricos nacionales
y locales.
Notas:
1. Para uso solamente con ventiladores de cielo raso que sean eléc-
tricamente reversibles y con capacidades de 1,6 A o menores. No se
debe usar con ninguna otra lámpara ni aparato eléctrico.
2. Se recomienda el uso de un circuito separado para los conjuntos
de luces de los ventiladores de cielo raso. Si el motor del ventilador
y el conjunto de luces se conectan juntos, el control de velocidad del
motor solamente se podrá usar cuando las luces estén apagadas.
Para usar el motor del ventilador y el conjunto de
luces juntos, este control se debe ajustar a alta
velocidad solamente.
Instrucciones de instalación:
1. Coloque el control de velocidad del ventilador
de cielo raso en la posición de Alta Velocidad
antes de instalar este control. No cambie el ajuste
de velocidad de su ventilador de cielo luego de
tener instalado el control de velocidad, puesto que
podría dañar su ventilador de cielo o el control All-
Fan.™
2.Verifique que el interruptor de pared del venti-
lador trabaja correctamente antes de la insta-
lación. Las conexiones incorrectas pueden dañar
el control y anularán la garantía.
3. Desconecte la energÌa eléctrica del ventilador
de cielo raso en el panel eléctrico principal. Retire
el fusible o coloque el disyuntor en la posición
“OFF” (apagado).
4.Vea la ilustración que muestra la instalación de
su control de velocidad All-Fan.™ Retire la placa
de la pared para exponer los cables y desconecte
el interruptor existente.
5. Si hay 4 alambres visibles, conecte cada alam-
bre del control de velocidad All-Fan™ a un alam-
bre negro. Si hay 2 alambres visibles, conecte cada uno a un
alambre del control de velocidad All-Fan.™ Use las tuercas de alam-
bres suministradas con el control para hacer las conexiones.
Consulte el Diagrama de Conexiones, que muestra la forma cor-
recta de conectar los alambres. Si su caja eléctrica contiene un
alambre de tierra, conéctelo al tornillo di tierra ubicado cerca de la
placa de montaje inferior.
6. Empuje los alambres y el control de velocidad, con mucho
cuidado, dentro de la caja del interruptor.Asegure el control de
velocidad All-Fan™ a la caja del interruptor con los dos tornillos
suministrados.
7. Monte la placa de la pared sobre el control con los tornillos
existentes.
8. Mueva la palanca deslizable a la posición “OFF” (apagada).
9. Vuelva a conectar la energía eléctrica en el panel eléctrico
principal.
10. Haga funcionar el ventilador de cielo raso moviendo la
palanca deslizable a la velocidad deseada.
Para la mejor operación: seleccione Alta Velocidad
hasta que el motor arranque y entonces seleccione la
velocidad deseada.
Quiet Fan Control
Ratings: 120 VAC, 1.6 A, 60 Hz
4-Speed Slide Control – Model 27181
Read and save these instructions.
Caution:
Risk of Electrical Shock!
All wiring must be performed in accordance with
national and local electrical codes. Use only to
control a single paddle-blade ceiling fan.
Notes:
1. For use only with electrically reversible ceiling fans
rated at 1.6 A or less. Not for use with any other light-
ing fixtures or electrical appliances.
2. Not for use with shaded-pole or
non-reversible motors. Not recom-
mended for use with the Hunter
Original.
® For Hunter Original ® series
fans, use Hunter control model
numbers 22691, 26591, or 22798.
3. Separate wiring is recommended
for ceiling fan light kits. If the fan
motor and light kit are connected
together, this fan speed control may
be used only when the light kit is OFF.
To use the fan motor and light kit
together, this control must be set to
HIGH speed only.
4. MEDIUM and both LOW speeds
may vary from the ceiling fan’s
factory-set speeds because of
motor variations.
HUNTER FAN COMPANY ALL-FAN™ CONTROL
LIMITED WARRANTY
The Hunter Fan Company makes the following limited warranty
to the original purchaser of the ALL-FAN™ Control (“Control”):
Your Control is warranted to be free from defects in material and
workmanship for a period of one year from the
date of sale. If the Control malfunctions or fails
within the warranty period due to a defect in
material or workmanship we will replace it free
of charge. IF THE ORIGINAL PURCHASER
CEASES TO OWN THE CONTROL, THIS WAR-
RANTY AND ANY IMPLIED WARRANTY,
INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE,
ARE VOIDED. THIS WARRANTY IS IN LIEU OF
ALL OTHER EXPRESS WARRANTIES. THE
DURATION OF ANY IMPLIED WARRANTY,
INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, IN
RESPECT TO ANY CONTROL, IS EXPRESSLY
LIMITED TO THE PERIOD OF THE EXPRESS
WARRANTY SET FORTH ABOVE FOR SUCH
CONTROL. This warranty excludes malfunctions
or failures which were caused by repairs by per-
sons not authorized by us, mishandling,
improper installation, modifications, or damage
to the Control while in your possession, or
unreasonable use. This warranty does not apply
to batteries or to deterioration or damage to the
product caused by the use of faulty batteries. To
obtain a replacement, return your Control
postage prepaid along with proof of purchase to Hunter Fan
Company Service Department at 2500 Frisco Avenue, Memphis,
Tennessee 38114. IN NO EVENT SHALL HUNTER FAN COMPANY
BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITA-
TIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE
ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
Wiring Diagram
120VAC
60Hz
Black
Hot
Neutral
Black
Fan