ClimaCool UCH SHC onDEMAND Simultaneous Heating and Cooling Heat Recovery - Manual (Page 5)

Contact your local ClimaCool representative or visit our web site at www.climacoolcorp.com to find out more about
SHC onDEMAND® and other heating and cooling solutions that may fit your application needs.
40% Footprint Savings
Over Typical
Simultaneous Systems
75% Footprint Savings
Over Traditional
Boiler/Chiller Systems
SHC onDEmanD® moDular CHillEr
UCH Series
30, 50, 70 and 85 tons
Configurable up to 1,000 tons
Available in 208, 230, 460 and 575 Volts
Patent Pending
Doc #: SHC-R_Brochure
ClimaCool works continually to improve its products. As a result, the design and specifications of each product at the time for order may be changed without notice
and may not be as described herein. Please contact ClimaCool’s Customer Service Department at (405) 815-3000 for specific information on the current design and
specifications. Statements and other information contained herein are not express warranties and do not form the basis of any bargain between the parties, but are
merely ClimaCool’s opinion or commendation of its products.
‘USGBC ® ’ and related logo is a trademark owned by the U.S. Green Building Council ® and is used with permission.
ClimaCool is a subsidiary of LSB Industries, Inc. – NYSE symbol: LXU
© ClimaCool Corp. 2010 1/13
15 S. Virginia
Oklahoma City, OK 73106
Phone: 405-815-3000
Fax: 405-815-3052
www.climacoolcorp.com
• •
Protect your bottom line and the environment simultaneously
The ClimaCool® SHC onDEMAND® modular
chiller helps reduce energy consumption and the
environmental impact of your heating and cooling
equipment by harnessing energy that is already
being produced but not used.
In addition, it provides all of the functionality of a
traditional boiler/chiller system while saving 75%
of the average footprint and up to 40% when
compared to typical simultaneous heat pump and
heat recovery systems.
The system allows connection flexibility for hot, cold
and source water loops. Typical simultaneous banks
limit configuration options to hot and cold water on
opposite ends whereas the SHC is fully configurable
to be same side or opposite side based on your
mechanical room design. Each module has the ability
to be utilized for heating or cooling onDEMAND to
precisely match building loads and provide compressor
run time equalization.
The SHC onDEMAND® system eliminates the need to
have separate equipment for heating and cooling while
saving installation costs, reducing the physical footprint
and overall operating costs. Innovative engineering
simplifies the simultaneous heating and cooling
process, taking multitasking to a whole new level.
LEED categories satisfied by the
SHC system are:
Sustainable Sites and Building Re-Use
Compact design shrinks mechanical room and
building footprint and allows modules to fit through
existing doors eliminating the need for demolition
and reconstruction.
Enhanced Commissioning and
Measurement and Verification
CoolLogic
Control System provides maximum flexibility with
BAS interface via native BACnet, LonWorks, Modbus
and N2 communications.
Optimized Energy Performance
Exceeds
ASHRAE 90.1 minimum efficiency by 30% or more.
Enhanced Refrigerant Management
Micro charge of chlorine-free and non-ozone
depleting refrigerant.
Thermal Comfort
Precise required heating
and cooling ensures the highest comfort for
building occupants.
True
Redundancy
Efficient
Cooling
Multitasking
Simultaneous
• •
Heating
Reliable
on DEMAND ® SIMULTANEOUS HEATING AND COOLING
on DEMAND ® SIMULTANEOUS HEATING AND COOLING
on DEMAND ®
SIMULTANEOUS HEATING AND COOLING
on
DEMAND ®
SIMULTANEOUS HEATING AND COOLING
95B0059N01