Analog Way OPS300 - Manual (Page 3)

OPS300 - Ref. OPS300
Rear Panel Description
RS-232 communication port
on a DB9 female connector
Power supply: IEC/EN/UL/CSA
60950-1, internal, autoswitchable
Universal Analog Computer/TV/HDTV inputs #1 to #5
SD/HD-SDI/3G-SDI inputs #1 & #2:
female BNC
Prelist and Main Audio Output
IP-LAN connector 3.5mm Jack Stereo
Connector input (unba-
lanced)
SD/HD-SDI/3G-SDI
output and SD/HDTV
output (DB9)
MCO Male Connector for unba-
lanced inputs #5 to #6
DVI #1 and DVI #2: Unbalanced
Input #7 and AUX: Balanced
A U D I O I N P U T / O U T P U T C O N N E C T I O N S H O M E M E N U
The Home Menu is the system’s top level menu, from which all others menus can be
accessed. To access a menu, press the [ MENU ] button. To navigate in the Home
Menu, please use the knob. To confirm, please use the [ ENTER ] button. You can also
return to the Home Menu by pressing the [ EXIT ] button.
- INPUT: select to configure the 1 individual input types and resolutions
- MAIN OUT: select to set Format and Rate for the Main screeen
- PREVIEW OUT: select to Format and Rate for the Preview screen
- VIDEO OUT: select to configure video output card settings
- PRESET: select to store and use presets
- IMAGE: select to change source image settings of an input
- KEYING/TITLING: select to access keying and titling controls and parameters
- LAYER: select to adjust layer size, position, border, transparency or transitions
- LOGOS/FRAMES: select to store (record), manage logos and frames
- AUDIO: select to access all audio input and output parameters
- CONTROL: select to access device software information, LAN settings, reset factory
settings, amongst other user oriented functions (see next page)
AUDIO OUTPUT
3.5mm Jack Stereo Connector
Inputs #1 to #4: Unbalanced connection
MCO Male Connectors *
Inputs #5 to #6: Unbalanced connection
Inputs DVI #1 & #2: Unbalanced connection Main Output: Balanced connection
Input #7 & (AUX): Balanced connection
4
L+
L-
R+
R-
BALANCED
L+
R+
L-
R-
GROUND(S)
Right
Left
Ground
5
6
L
R
L
R
UNBALANCED
LEFT
LEFT
RIGHT
RIGHT
GROUND(S)
Input #5
Input #6
H O W TO A D J U S T A S O U R C E ?
IMAGE (A3)
HOME MENU (extract)
Auto Centering (R1)
Blanking Adjust (R2)
Cropping (R2)
Optimize (R1)
Under/Over (R3)
Aspect IN
Aspect OUT
Colorimetry
Advanced (R2)
2:2 Pulldown (R7)
3:2 Pulldown (R8)
Reset settings
Force 4:3 (R9)
H position
H position
V position
V position
H size
H size
Phase
Underscan
Native
LetterBox_2_35
Centered
Contrast
Red Level (R5) Component Level (R2)
Pillar Box
1_1
Hue (R6)
Blue Level (R5) Motion Correct. (R11) *
V size...
V size...
H Total
Overscan
LetterBox_1_78
Full screen
Brightness
Anamorphic
Cropped
Color
Green Level (R5)
(A3) displayed when an
input is active
(R1) Analog Computer Input
(R2) Analog Input
(R3) Video Input
(R4) EDTV/HDTV Input
(R5) RGB or YUV or YC or CV
(R6) NTSC Input
(R7) Interlaced 50 Hz
(R8) Interlaced 60 Hz
(R9) SDTV
The Menu allows to improve the thres-
hold of the comb filter.
0% means no adjustments and 100%
is the max. The setting is manual with
a visual correction.
The result is the removal of the aliasing
in the moving picture.
* Motion Correction
DVI connectors: DVI-D inputs #1 and #2 on the DVI-I
digital pins, and Universal Analog inputs #6 & #7 on
the DVI-A analog pins. Use the included break-in cable.
Outputs #1 & #2: female HD15, DVI-I
(simultaneous analog and digital outputs)
* A set of 3 audio 10-pin screw terminals is provided with the device. The figure repre-
sents the lower or upper connector.