Agri-Fab H.D. Lawn Roller 45-01791 - Manual (Page 2)

REPAIR PARTS
303 West Raymond
Sullivan, IL. 61951
217-728-8388
www.agri-fab.com
ASSEMBLY INSTRUCTIONS
(SEE ILLUSTRATION BELOW)
1. Assemble bearings (Ref. 5) into hitch tubes (Ref.
3) so that bearing flange is against outside of hitch
tube. (You may need to place a block of wood
against bearing and carefully tap with a hammer.)
2. Place hitch tubes (Ref. 3) onto both ends of roller
shaft. Assemble a flat washer (Ref. 6) onto each
end of roller shaft and secure with two cotter pins
(Ref. 12).
3. Assemble scraper bar (Ref. 2) to hitch tubes (Ref.
3) using two hex bolts (Ref. 9) and hex lock nuts
(Ref. 10).
Do not tighten yet.
4. Assemble ends of hitch tubes (Ref. 3) together
using two hex bolts (Ref. 7) and hex lock nuts (Ref.
10).
Do not tighten yet.
5. Assemble hitch brackets (Ref. 4) to hitch tubes
(Ref. 3) using two hex bolts (Ref. 8) and hex lock
nuts (Ref.10 ).
Do not tighten yet.
6. Tighten bolts and nuts starting with scraper bar
(Ref. 2), then ends of hitch tubes (Ref. 3), and
finally hitch brackets (Ref. 4).
7. Install hitch pin (Ref. 13) through hitch brackets
(Ref. 4) and secure with hair cotter pin (Ref. 14).
1 62377 1 Roller Ass'y
2 24867 1 Scraper Bar
3 48361 2 Hitch Tube
4 24192 2 Hitch Bracket
5 43632 2 Bearing, Plastic
6 43528 2 Flat Washer, 1"
7 46782 2 Hex Bolt, 5/16-18 x 3"
8 43224 2 Hex Bolt, 5/16-18 x 2-1/4"
9 43084 2 Hex Bolt, 5/16-18 x 1-3/4"
10 43064 6 Hex Lock Nut, 5/16-18
11 43709 1 Plug, Lawn Roller
12 43501 2 Cotter Pin, 5/32" x 1-1/2"
13 47623 1 Hitch Pin
14 43343 1 Hair Cotter Pin 1/8"
1
6 5
9
3
10
4
8
10
7
3
9
5
6
11
2
10
10
12
12
Ref. Part Qty. Description
No. No.
Ref. Part Qty. Description
No. No.
Printed in USA Form No. 48362 (REV. 5/02)
SAFETY PRECAUTIONS
1. Never attach a garden hose to the fill/drain hole
when filling. Dangerous pressure build up could
occur inside roller.
2. Do not fill roller to maximum weight without check-
ing capability of vehicle to safely pull and stop.
3. Never use roller up and down hills; always work across
hills and slopes.
4. Use caution when turning, slowing or stopping.
5. Always drain roller to keep from freezing.
SPECIFICATIONS:
Roller Drum: 24" Dia. x 36" Wide, Welded Steel
O.A. Width: Approximately 40"
Bearings: 1" I.D., Replaceable
Tow Hitch: Std. Pin Type - 1/2" Hole
Weight w/ Water: Up to 640 Lbs. Filled with Water
(Note: May be filled with sand)
Approx. Sh. Wt.: Approximately 105 Lbs.
the fastest way to purchase parts www.speedepart.com