Draw-Tite 75774 MAX-FRAME RECEIVER User Manual

Installation instructions, Mercedes glk350, Part numbers

Advertising
background image

Offset hole towards passenger’s side of vehicle

Long sides of

blocks vertical

Tape bolt to

hitch bracket

Installation Instructions

Mercedes GLK350

All Models including

4-Matic

& RWD

Part Numbers:

75774, 87636

44690, 78303

U-Haul

Hitch Shown In Proper Position

Equipment Required:

Wrenches: 3/4”, 7/8”

Drill Bits: None

Fastener Kit: 75774F

Do Not Exceed Lower of Towing Vehicle Manufacturer’s Rating or

Wiring Access Location: SUV 3, SUV 4

7

8

Vehicle cross member

Back View of vehicle cross

member attachment showing both

Other Tools: Tape

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Carrying

Ball Mount

4000 (1814 Kg)

600 (272 Kg)

Vehicle frame
cross member

Tape

5

4

2

6

8

4

5

1

2

3

Vehicle

Forward

Vehicle end panel

Bumper fascia

Clamp Brackets

Block

RWD Models-Note! You may have to insert the clamp bracket with
nuts through the crossmember opening from the rearward side and
locate on forward side of crossmember.

Trunk Pan

1.

You may have to remove or bend up small plastic fascia tabs sticking out on bottom of bumper fascia before installing hitch.

See picture next page.

2.

Install Clamp Brackets to vehicle cross member and install bolts and lock washers and torque to specs below before installing

hitch. Bracket with weld-nuts goes on forward side of cross member. Be sure to orient offset hole to vehicle passenger’s side

as shown. See picture next page. See note above regarding RWD models.

3.

Tape blocks and bolts to hitch uprights as shown before raising hitch in to place as shown above. Blocks should be positioned

with long sides vertical.

4.

Raise hitch up under vehicle being careful not to push bolts out of hitch that are taped in to place. Install conical washer &

nuts loosely to hold hitch in place. Rotate hitch and insert 5/8” thick block between hitch bar & clamp bracket and install 3”

long hex bolt and conical washer. Torque 3” long bolt to specs below. Torque (2) rearward 1/2” nuts to specs below.

Tighten 1/2”-13 Gr.5 bolts /nuts with torque wrench to 75Lb.-Ft. (102 N*M).

z

2013 Cequent Performance Products, Inc. – Printed in Mexico

Sheet 1 of 6

75774N

5-31-13

Rev. B

Qty. (2)

1/2”-13 X 1-1/2” Gr.5 Carriage Bolt

Qty. (2)

1/2” Lock Washer

Qty. (3)

1/2” Conical Toothed Washer

Qty. (1)

1/2-13 X 3” Gr.5 Hex Bolt

Qty. (2)

1/2”-13 Hex Nut

Qty. (1)

5/8” X 1-1/2” X 2” Block

Qty. (2)

1/2”-13 X 1-1/2” Gr.5 Hex Bolt

Qty. (2)

1/4” X 1-1/2” X 2” Block

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Form: F205 Rev A 5-6-05

1

2

member attachment showing both

Clamp Brackets. Bracket with

weld-nuts on forward side.

4

3

5

6

8

7

Fasteners typical

both sides.

Note!

Install Clamp

Brackets & bolts in to place

and torque to specs below

before raising hitch in to place.

Back view showing

block & bolt taped to

hitch upright before

raising hitch in to place.

Tape

1

2

3

4

Advertising