INSTEON RemoteLinc 2440_2440BK Quick Start User Manual

Quick start guide, Remotelinc, Insteon

Advertising
background image

Page 1 of 1

Rev. 07-03-2012

*Setup Modes automatically time out after 4 minutes.

This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas

produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.

Dedicated

simultaneous-

control

buttons

Customizable

label insert

Dedicated

Dim/Brighten

buttons

Setting Up RemoteLinc

1)

RF-only devices require at least one dual-band INSTEON

device for communication. For the best INSTEON network

performance, be sure you have properly installed at least

two Access Points or other dual-band INSTEON devices.

2)

Remove the battery compartment from the rear of

RemoteLinc and install four AAA batteries.

3)

Replace the battery compartment door.

NOTE: Use alkaline batteries, or high quality rechargeable

batteries. A fully charged set of alkaline batteries will provide

approximately 1,500 – 2,000 button taps.

Quick Start Guide

RemoteLinc

– INSTEON

®

Wireless Remote Control

Model #2440BK

Introduction

RemoteLinc allows you to use the power of INSTEON to control

your home with the convenience of a handheld wireless

controller. RemoteLinc can control up to six scenes and features

a customizable label insert.

Using RemoteLinc as an INSTEON Controller

1)

On RemoteLinc, press and hold the On button of the button pair you wish to use until it beeps (10 seconds).

RemoteLinc’s status LED will begin blinking.

2)

Set the responder to the state you want to activate from RemoteLinc.

3)

Press and hold the responder’s Set button for 3 seconds

RemoteLinc will beep and its status LED will turn off.

4)

Test link by tapping the On/Off buttons you just linked to on RemoteLinc.

The responder should respond appropriately.

INSTEON Limited Warranty – INSTEON warrants to original consumer of this product for a period of 2 years from date of purchase, this product will be free

from defects in material and workmanship and will perform in substantial conformity with its Owner's Manual. Warranty shall not apply to defects caused by

misuse or neglect.

Protected under U.S. and foreign patents (see www.insteon.com) © Copyright 2012

INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845, www.insteon.com

Using RemoteLinc

Each button on RemoteLinc has a dual purpose. Linked responders will behave differently depending on what button you

press, and whether it is tapped or pressed and held.

Button

Applies To

Tap

Press and Hold

On

Device(s) linked to that specific button pair

Ramp to On-Level

Brighten until release

Off

Device(s) linked to that specific button pair

Ramp to Off

Dim until release

All On

All devices linked to RemoteLinc

Fast-on

Brighten until release

All Off

All devices linked to RemoteLinc

Fast-off

Dim until release

Brighten

Device(s) linked to last On/Off button pushed

Brighten by 3 levels (out of 32)

Brighten until release

Dim

Device(s) linked to last On/Off button pushed

Dim by 3 levels (out of 32)

Dim until release

NOTE: Non-dimming responders will not be affected by brighten/dim commands or pressing and holding any of the buttons.

Complete Instructions, Troubleshooting and Tech Support

Owner’s Manual and Quick Start Guide:

http://www.insteon.com/support

Call: INSTEON Support Line at 800-762-7845

On/Off

button

pairs

Status

LED

Advertising