intimus 45 CC4 - Manual (Page 7)

MATERIAL JAM IN THE MACHINE:
(Auto reverse function)
If a jam is caused by too much material being fed in
the following happens:
- The cutters jam, then run in reverse for a short
time (material is released) and stop. The motor
switches off. The control display (6) comes
on.
Proceed as follows:
Paper jam in paper feed slot (12)
- Remove the paper that has been fed back.
- The cutters now run forwards automatically and
shred the remaining paper in the cutters. During
the forward run the forward button (3) LED
display comes on. The control display (6)
goes out.
- Continue shredding with less paper.
Material jam in CD/DVD feed slot (13)
- Remove the returned material.
Remove the material carefully
because there is the risk of being
injured by the sharp cut surfaces.
- The remaining material to be cut is now
automatically fed to the cutters again and
shredded. During the forward run the forward
button (3) LED display comes on. The control
display (6) goes out.
- If the material to be cut has gone through continue
shredding with the right amount of material.
- If necessary, switch the cutters manually
alternately from forward to reverse until the
material has gone through completely and been
shredded.
SIMULTANEOUS MATERIAL FEED:
Should material be fed into the two feed slots at the
same time the following happens:
- The cutters jam, then run in reverse for a short
time (material is released) and stop. The motor
switches off. The control display (6) comes
on.
- Take the material out of one of the slots.
- Press the forward button (3) briefly. The material
in the other slot is fed to the cutters and shredded.
The control display (6) goes out.
LIGHT BARRIER COVERED
WHEN DOOR OPENED:
Should there still be material in one of the two feed
slots when the door is opened, the motor switches
off and the cutters stop. The control display (6)
comes on.
Close the door and acknowledge the status by
pressing the forward button (3) briefly. The existing
material is fed to the cutters and shredded.
LIGHT BARRIER COVERED
WHEN MACHINE TURNED ON:
Should there still be material in one of the two feed
slots when the machine is switched on the control
display (6) comes on.
Remove the material and acknowledge the status
by pressing the forward button (3) briefly.
MOTOR PROTECTION:
Should the motor be overloaded it switches off. The
control display (9) comes on.
The machine can be started again after a cooling
down period of about 25 – 40 minutes (depending
on the model and the room temperature).
ELECTRICAL FAULT:
If the control display (9) flashes together with
the function button (2) LED display or only the
control display (8) flashes there is an electrical
fault. The machine cannot be started.
In this case please contact your dealer.
FAULT CHECK LIST:
Should the machine not work, check the following
points:
- is the plug connected to the power supply?
- is the door closed?
- is the paper collection bag full?
Follow the instructions for “EMPTYING THE
PAPER COLLECTION BAG“.
- Is the CD/DVD collection container full?
Follow the instructions for “EMPTYING THE CD/
DVD COLLECTION CONTAINER”.
- Is there a material jam in the machine?
Follow the instructions in “MATERIAL JAM IN
THE MACHINE”.
- Is the motor overloaded?
See “MOTOR PROTECTION”.
If none of these test points apply, please
contact your dealer.
17
90972 5 04/13
45SC2 45CC3 45CC4 45CC5 45CC6 60SC2 60CC3 60CC4 60CC5 60CC6
MALFUNCTIONS
MAINTENANCE / DISPOSING
TECHNICAL DATA SPECIAL ACCESSORIES
GB
CUTTER MAINTENANCE (CROSS CUT):
Cross cut cutters must be oiled after a specific
operating time.
If the control display (7) comes on proceed as
follows:
Open the door. The control display (8) comes on and
the reverse button (4) LED display as well as the control
display (7) flashes. Remove the oil reservoir (17) (Fig. 6)
from the holder in the door and close the door again.
Pour a little oil onto a sheet of paper and then feed this
through the paper feed slot (12) onto the cutters.
The paper is drawn in and in this way the oil is distributed
to the cutters.
Note: This procedure is acknowledged as follows to turn
off the display after the cutters have been oiled:
- Open the door until the control display (8) lights up. The
control displays (7) and (4) flash.
- Press the reverse button (4) and keep it held down until
the control display (7) goes out.
CLEANING THE PHOTOCELLS (Fig. 5):
If paper particles should come to rest in the inlet guide (for
example after a paper jam) it is possible that the machine will
not turn off, due to the broken light barrier.
To remove these paper strips and also to clean the photocell,
pass another sheet of paper through the feed slot, or switch
the machine to reverse and wipe both “eyes” of the photocell
with a brush.
- Close the door again.
The cutters now start a cleaning cycle automatically (forward
and reverse run) and then switch off. The machine is ready
for use again. Should you need to re-order the special oil see
“SPECIAL ACCESSORIES”.
AUTOMATIC ENERGY SAVING:
If the machine is not used for a while it automatically switches
off after about 5 minutes. The function button (2) LED display
for “Ready” goes out. Press the function button briefly to
turn it on again.
DISPOSING OF THE MACHINE:
Dispose of the machine in an environmentally
friendly fashion at the end of its useful service life.
Do not dispose of any of the parts included in the
machine or its packaging with household waste.
fig. 5 fig. 6
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
7
Model Typ Cutting width Cutting capacity Working width Noise level Dimensions Weight
paper / CD,DVD paper / CD,DVD W x D x H
intimus 45SC2 278-4S 3.8 mm / 8 mm 22-24 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 650 mm 31 kg
intimus 45CC3 278-4C 3.8x30 mm / 8 mm 13-15 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 650 mm 32 kg
intimus 45CC4 278-2C 1.9x15 mm / 8 mm 10-11 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 650 mm 32 kg
intimus 45CC5 278-1C 0.8x12 mm / 8 mm 5-6 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 650 mm 32 kg
intimus 45CC6 278-1CF 0.8x4.5 mm / 8 mm 5-6 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 650 mm 32 kg
intimus 60SC2 279-4S 3.8 mm / 8 mm 22-24 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 770 mm 33 kg
intimus 60CC3 279-4C 3.8x30 mm / 8 mm 13-15 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 770 mm 34 kg
intimus 60CC4 279-2C 1.9x15 mm / 8 mm 10-11 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 770 mm 34 kg
intimus 60CC5 279-1C 0.8x12 mm / 8 mm 5-6 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 770 mm 34 kg
intimus 60CC6 279-1CF 0.8x4.5 mm / 8 mm 5-6 sheets* / 1 piece 235 mm app. 55 dB(A) 450 x 390 x 770 mm 34 kg
Model Power supply data
supply voltage/frequency · current consumption · power
intimus 45/60SC2 220-230V/50Hz · 3,0 amps · 0,7 kW 120V/60Hz · 5,6 amps · 0,7 kW 100V/50/60Hz · 7,0 amps · 0,7 kW
intimus 45/60CC3+CC4+CC5 220-230V/50Hz · 3,0 amps · 0,55 kW 120V/60Hz · 5,6 amps · 0,55 kW 100V/50/60Hz · 7,0 amps · 0,55 kW
intimus 45/60CC6 220-230V/50Hz · 3,0 amps · 0,7 kW 120V/60Hz · 5,6 amps · 0,7 kW 100V/50/60Hz · 7,0 amps · 0,7 kW
Description Order-No.
Plastic bag, 440x330x600x0.05 mm (45) 83079
Plastic bag, 440x330x950x0.05 mm (60) 99977
Lubricant, 110 ml bottle 88035
Note: For orders of special accessories and spare
parts, please contact your dealer.
* based on A4-paper 70g/m² at 230V/50Hz
Pre-fusing (slow-blow): 220-230V = 10 amps / 120V = 15 amps / 100V = 15 amps