1hour 1 hour – King Technology Aqua Smarte Plus Pool Awake! User Manual
Page 2
After balancing the pool water and inserting a
new Aqua Smarte Plus Mineral Activator, insert
Aqua Smarte Plus Shine
using steps 1 through 8.
Water Balance Guidelines
pH:
7.2 – 7.8
Total Alkalinity: 60 – 120 ppm
Calcium Hardness: 150 – 400
Total Dissolved Solids: <1500
Stabilizer: 20 – 80 ppm
Free Chlorine:
0.5 – 1.0 ppm
1. With the circulation
system off, set control
dial to lowest setting and
remove the cap to the
Aqua Smarte or Aqua
Smarte Plus System.
COLORED
CAPS
2. Remove caps from Aqua
Smarte Plus Shine with a
pliers or other suitable tool.
3. Turn Aqua Smarte Plus
Shine over so open ends
face down and insert into
the center of the Aqua
Smarte Plus Mineral
Activator. The ends of the
pac will align with an
L-shaped key in the
system. DO NOT FORCE.
4
4. Replace cap on Aqua
Smarte or Aqua Smarte
Plus System and set dial
to
Setting 5.
5. Turn on pump and allow
1 hour for the product to
slowly dispense into the
pool. If after 1 hour, the pac
still contains some ingredi-
ent, re-insert, replace cap
and run the circulation for
an additional 30 minutes.
6. Remove the empty Aqua
Smarte Plus Shine and
discard or recycle.
1. Aqua Smarte Plus Shine™
SHINE
™
Eliminate
s Contam
inants
for
Crystal C
lear Wa
ter
SHINE
™
Eliminates Contaminants for
Crystal Clear Water
WE RECYCLE
2
3
7. Replace cap on Aqua
Smarte or Aqua Smarte Plus
System and allow circulation
to run at least 15 minutes
before inserting any other
Aqua Smarte Plus products.
After balancing the pool water and inserting a
new Aqua Smarte Plus Mineral Activator, insert
Aqua Smarte Plus Shine
using steps 1 through 8.
Water Balance Guidelines
pH:
7.2 – 7.8
Total Alkalinity: 60 – 120 ppm
Calcium Hardness: 150 – 400
Total Dissolved Solids: <1500
Stabilizer: 20 – 80 ppm
Free Chlorine:
0.5 – 1.0 ppm
1. With the circulation
system off, set control
dial to lowest setting and
remove the cap to the
Aqua Smarte or Aqua
Smarte Plus System.
COLORED
CAPS
2. Remove caps from Aqua
Smarte Plus Shine with a
pliers or other suitable tool.
3. Turn Aqua Smarte Plus
Shine over so open ends
face down and insert into
the center of the Aqua
Smarte Plus Mineral
Activator. The ends of the
pac will align with an
L-shaped key in the
system. DO NOT FORCE.
4
4. Replace cap on Aqua
Smarte or Aqua Smarte
Plus System and set dial
to
Setting 5.
5. Turn on pump and allow
1 hour for the product to
slowly dispense into the
pool. If after 1 hour, the pac
still contains some ingredi-
ent, re-insert, replace cap
and run the circulation for
an additional 30 minutes.
Dispense Aqua Smarte
Plus Optimize to establish
an initial chlorine level
in the pool following the
same steps 1 through
8 for Aqua Smarte Plus
Shine.
All components are recyclable when finished
dispensing.
6. Remove the empty Aqua
Smarte Plus Shine and
discard or recycle.
1. Aqua Smarte Plus Shine™
2. Aqua Smarte Plus Optimize™
SHINE
™
Eliminate
s Contam
inants
for
Crystal C
lear Wa
ter
SHINE
™
Eliminates Contaminants for
Crystal Clear Water
WE RECYCLE
2
3
WATER MANAGEMENT SYSTEM
WATER MANAGEMENT SYSTEM
1
HOUR
1
HOUR
8. Repeat steps 1-7 if
additional Aqua Smarte
Plus Shine is required.
7. Replace cap on Aqua
Smarte or Aqua Smarte Plus
System and allow circulation
to run at least 15 minutes
before inserting any other
Aqua Smarte Plus products.
Dispense Aqua Smarte
Plus Optimize to establish
an initial chlorine level
in the pool following the
same steps 1 through
8 for Aqua Smarte Plus
Shine.
All components are recyclable when finished
dispensing.
2. Aqua Smarte Plus Optimize™
8. Repeat steps 1-7 if
additional Aqua Smarte
Plus Shine is required.