Laurel Metal Microcoin QL - Manual

Installation Instructions
1) Install or replace long drop bracket on faceplate
2) Coin cup may need to be removed and re-attached
in order to mount faceplate
3) Place Microcoin QL into the bracket and secure
with lockable brace
4) The two holes on the lockable brace are designed to
fit over the screw heads on the back of the QL
coin mechanism
Wiring Instructions
Note 1: The Blue wires are interchangable
Note 2: Dixmor timer users should skip to 4
1) Connect the Black and a Blue wire to the 24 VAC
2) Connect the Yellow wire to the Neutral
3) The other Blue wire (see note 1) connects to the
timer coin pulse
4) Dixmor Timers only:
Connect Black wire to 24 VAC
Connect Yellow and a Blue wire to Neutral
Connect the other Blue wire to timer coin pulse
Note 1: Coins that are preprogrammed should not be
programmed a second time.
Note 2: Programmed coins can be turned on/off with
out re-programming; Use Enable or Disable.
1) Press Button 3 times quickly. Indicator light will show
yellow flashing. LED will show "1" to represent
category number 1
2) Pressing the Button a second time will program the
coin to the next category #, up to 5
3) When the appropriate category is showing on the LED,
drop 10 different samples through the acceptor.
4) When the 10th coin has been sampled the Indicator
light is a solid yellow
Indicator Light
Button
LED Display
Indicator Light can
show Green, Yellow,
and Red
5) Press Button once. LED will read "0", this is the value
6) Press the Button one time for every 0.25 increment the
token is worth, ie."4" gives the token a $1.00 value
(Press the Button 6x and the LED will read "6",
the token value will be $1.50), up to $2.50 value.
Trouble Shooting Guide
Problem Possible Cause Action
All coins rejecting No Power, no ind. light Check incoming voltage
Low Voltage Monitor Voltage
Water in coin path Allow to dry
Programming mode Return to programming
interrupted mode and follow guide
to reprogram most
recent coin, if this mode
is started and not
completed all coins rej.
One coin rejecting Coin disabled Enable coin
Not programmed Program coin
Slightly different coin Reprogram coin using 10
different samples
"look alike" coin Coins is actually different
and can be accepted by
programming on add'l
category
Timer not counting 24 v. / common reversed Refer to wiring section
Coin jam Full coin box Empty box and QL
QL sitting crooked Reinsert into bracket
Coin path obstructed Remove foreign object
Microcoin QL Warranty
Two year parts warranty from date shipped from factory
Two year labor warranty from date shipped from factory
Repair or replacement at factory option
Damage due to improper wiring, corrosion, vandalism,
or water damage is not covered for any reason
Customer is responsible for the freight charges regardless
of cause or outcome
Please include information for all warranties and service
as to the nature of the problem, daytime phone #, return
shipping address and any other pertinent information.
Programming and trouble shooting information
available at www.hpws.com
Email questions to [email protected]
3901 East 41st Ave Denver, CO 80216 (303) 322-2232
Disable
Used to disable a coin temporarily or for long periods of time
1) Press twice quickly, Indicator Light will flash red
2) Drop coin one time, Ind. Light will show solid green
Enable
Used to reactivate a coin, not required for programming
1) Press Button 1 time, Indicator Light will flash green
2) Drop coin one time, Ind. Light will show solid green
7) When the appropriate value is assigned, press and
hold the Button for 2 full seconds
8) When the Button is released the Indicator Light will
show solid green
9) Test the coin acceptor. When complete note the
token and value on the side of the Microcoin QL
Programming Instruction
Do not program in nickels, dimes, quarters
or dollar coins. They are preprogrammed on
lines 7-12 and can be turned on/off infinitely.
Microcoin QL
Quantum Leap