LEADER LV7800 - Manual (Page 4)

28
LV 5800/LV 7800 Platform Options
This SDI input unit can be installed into to
the input slot of an LV 5800 (multi monitor)
or into an LV 7800 (multi rasterizar). You can
install a maximum of four LV 58SER01A
units into these instruments. By operating
the instrument, you can display SDI signals'
video signal waveforms, vector waveforms,
pictures, error detection results, and so on.
Video Formats and
Corresponding Standards
Single Link System Video
Dual Link System Video
Ancillary data standard
Embedded audio standard
Input/Output Connector
SDI Input
Input Connector
Maximum Input Voltage
External Sync Signal Input
Input Signal
Input Connector
SDI Output
Output Connector
During single link
During dual link
Output Impedance
Output Voltage
Output Return Loss
Waveform Display
Waveform Operation
Display Mode
Overlay display
Parade display
Gain Adjustment
Blanking Period
YC
B C R →GBR conversion
Pseudo-Composite Display
Timing Display
Line Select
Image Quality Adjustment
Vertical axis
Sensitivity
Gain
Variable Gain
Amplitude Accuracy
Horizontal Axis
Line Display
Display Format
Magnification
Cursor Measurement
Configuration
Amplitude Measurement
Time Measurement
Frequency Display
SMPTE 291M
HD-SDI: SMPTE 299M SD-SDI: SMPTE 272M
BNC connector 2 connectors
For single link
A ch / B ch 2 systems
For dual link link A / link B 1 system
±2 V (DC + peak AC )
Tri-level sync or NTSC/PAL black burst
BNC connector 1 system 2 connectors
BNC connector 2 connectors
Reclocks serially and outputs the input signal.
A ch/B ch switchable
1 system
B ch fixed 1 system
link A / link B 1 system
75 Ω
800 mVp-p ±10 %
15 dB or more (5 MHz to serial clock frequency)
Displays component signals overlaid
Displays component signals side by side
x1 / x5 / variable
Show / hide selectable
Converts YC
B C R signals into GBR and displays the result.
Digitally converts component signals into composite
signals and displays the result.
Displays by calculating Y-C
B and Y-C R
Uses bowtie signals
Displays the selected line
Brightness adjustment
V scale 0 V to 0.7 V, -0.3 V to 0.7 V
% scale 0 % to 100 %, -50 % to 100 %
x1, x5, and variable
x0.2 to x2.0
±0.5 %
Overlay: 1H, 2H
Parade: 1H, 2H, 3H
Timing: Y-C B ,Y-C R
4Y Parade*1: 4H
*1 As for 4Y parade mode, two LV 58SER01A (SDI
INPUT unit) should be inserted, and four inputs
need to synchronize in the same format each
other together.
x1, x10, x20
Horizontal cursors: 2 cursors (REF and DELTA)
Vertical cursors: 2 cursors (REF and DELTA)
Measured in [%] and [V]
Displayed in [usec] or [msec]
Displays the frequency in which the time between
FEATURES
• 2-Channel Serial Digital I/O
An SDI input unit contains 2 channels of SDI input connectors. The two
connectors can also function as a dual link input of a single channel. SDI
output that is reclocked using a serial signal is provided for each input. In
addition, the SDI signal that is inputted to the ACH or the BCH can be
outputted respectively from the ACH/BCH Reclockout output connector
by interlocking with the input key of the front panel.
• Video Signal Display Function
In addition to displaying the video waveforms, vectors, and pictures of
the SDI signal on a full screen, 2- and 4-screen multi display can be
shown. The multi display allows arbitrary combination of a single or mul-
tiple input signals to be displayed.
(Multi display in which link A and link B are separated during dual link
operation is not allowed.)
• Error Detection Function
Detects various errors related to the SDI, embedded audio, and
ancillary data including CRC errors and EDH errors.
• Ancillary Data Analysis
Supports various types of ancillary data for analysis display. In particular.
• 5 BAR DISPLAY
The 5 BAR display allows simultaneous monitoring of component
and composite gamut
.
• SDI-EXT REF Phase Difference Display Function
The SDI-EXT REF phase difference display function shows the phase dif-
ference between the SDI signal and the external sync signal (EXT REF).
• Simultaneous Monitoring of Component and Composite
Gamut Using the 5 Bar Displays
• Closed Caption Display Function
• Embedded Audio Demultiplex Function
The unit is equipped with a function for demultiplexing the embed-
ded audio signal.
Level meter and Lissajous displays can be achieved when used in
combination with the digital audio unit (LV 58SER40A). The signal can
also be output as AES/EBU.
• Dual link input
• AFD Display
• CIE 1931 XY Chromaticity Diagram Display
The CIE1931 XY Chromaticity Display (CIE chart) provides a X-Y vector
display allowing for the evaluation and analysis of color in the XYZ coor-
dinate system. Chromaticity markers, Planckian locus curve with color
temperature and cursors are also provided.
IOPTION
• FS 3033 Cinelite II (Cinelite and Cinezone)
LV 58SER01A SDI INPUT SPECIFICATIONS
Ⅱ
option
Cinelite
ANC Date Viewer AFD
CIE Chart Temp Display
Cinezone
LV 58SER01A SDI INPUT (HD-SDI, SD-SDI, HD-SDI DUAL) Plug-In Unit
CINELITE On-Picture
Measurements,
CINEZONE false color
displays and peaking
function facilitate
quick camera foucus
and exposure setups.
Format Quantization Scanning Frame (Field) Rates
Corresponding
Supported
Y,C B ,C R
4:2:2
10 bit
1080i 60/59.94/50 SMPTE 274M
SMPTE 292M
1080p 30/29.97/25/24/23.98
1080PsF 30/29.97/25/24/23.98
SMPTE RP 211
SMPTE 292M
720p
60/59.94/50/
30/29.97/25/24/23.98 SMPTE 296M
SMPTE 292M
525i 59.94
SMPTE 259M
625i 50
Format Quantization Scanning Frame (Field) Rates
Corresponding
Supported
RGB
4:4:4
10 bit
1080p 30/29.97/25/24/23.98
SMPTE 372M
(1920x1080)
1080PsF 30/29.97/25/24/23.98
1080i 60/59.94/50
12 bit
1080p 30/29.97/25/24/23.98
1080PsF 30/29.97/25/24/23.98
1080i 60/59.94/50
Y,C B ,C R
4:2:2
10 bit 1080p 60/59.94/50
12 bit
1080p 30/29.97/25/24/23.98
1080PsF 30/29.97/25/24/23.98
1080i 60/59.94/50
GBR 4:4:4
(2K)
12 bit
1080p 24/23.98
(2048x1080)
1080PsF 24/23.98
AFD
SD-SDI
HD-SDI
2K
Dual Link
Leader Instruments Corporation web : http://www.LeaderUSA.com Tel. : 1 (714) 527‐9300
6484 Commerce Drive, Cypress, CA 90630 e‐mail : [email protected] Fax : 1 (714) 527‐7490