Lectrosonics SRa Series - Manual (Page 16)

SRa5P and SRa Dual Receivers
LECTROSONICS, INC. 16
HYB
SETUP
(item)
1 80
652.800
2 AF
657.500
TUNING
MENU
BACK BACK
MENU
Receiver 1
Pilot Tone
ON\OFF
Hold MENU and
hold DOWN
Hold MENU
and hold UP
Mute Audio on
Receiver 1
Mute Audio on
Receiver 2
Press
UP/DOWN
to select
Press
UP/DOWN
to adjust
RECEIVER 1
00 00 00
RECEIVER 2
SEL
BACK
SEL
SEL
BACK
SEL
SCANNING
STARTS
SEL
SCANNING
STOPS
Press
SEL to
select
receiver
Press UP/DOWN
to scroll
frequency
Press both
UP and DOWN
to ZOOM
Press UP/DOWN
to scroll
frequency
MENU
BACK
Setup Window
Main Window
Receiver 1
Receiver 2
Press UP/DOWN to change frequency
Press UP/DOWN to change frequency
DIVMOD
RATIO
Press
UP/DOWN
to select
NOTE: Main Window will look like this
when the RATIO DIV mode is selected.
LEVEL LEVEL
00
DOWN
DOWN
DOWN
DOWN
DOWN
DOWN
DOWN
DOWN
DOWN
SEL
BACK
COMPAT
HYB HYB HYB
COMPAT
B3 B3
2
4A
1
5E
BACK
BACK
ZOOM GRAPHIC
BACK
SEL
BACK
RECEIVER 1 RECEIVER 2
Press
UP/DOWN
to select
SEL
BACK
TUNING TUNING
RECEIVER 1 RECEIVER 2
Press
UP/DOWN
to select
a
NOR
a
NOR
Press
SEL to
select
receiver
Press
SEL to
select
receiver
SEL
BACK
SmtNR SmtNR
RECEIVER 1 RECEIVER 2
Press
UP/DOWN
to select FUL NOR
Press
SEL to
select
receiver
FUL NOR
LEVEL
SETUP
SCAN
SETUP
DIVMODE
SETUP
COMPAT
SETUP
SmtNR
SETUP
PHASE
SETUP
TXBAT
SETUP
MIXMODE
SETUP
TONE
SETUP
SEL
BACK
PHASE PHASE
RECEIVER 1 RECEIVER 2
Press
UP/DOWN
to select
Press
SEL to
select
receiver
+ +
SEL
BACK
TXBAT TXBAT
RECEIVER 1 RECEIVER 2
Press
UP/DOWN
to select
Press
SEL to
select
receiver
SEL
BACK
MIXMODE Press
UP/DOWN
to select
SEL
BACK TONE?
RECEIVER 1 RECEIVER 2
Press
UP/DOWN
to select
Press
SEL to
select
receiver
00 +05
Tone will be enabled
when level is set with
the UP/DOWN buttons TONE?
00 +05
LVL 1K
RECEIVER 1
00 +05
BACK
UP
UP
UP
UP
UP
UP
UP
UP
UP
DOWN
RATIO 80
652.800
When the receivers are combined in the
RATIO DIVERSITY mode, the frequency
screen will look like this.
MIXBOTH
DOWN
MIXTRIM
SETUP SEL
BACK
MIXTRIM
UP
00 +05
MIXTRIM
Press
SEL to
select
receiver
00 +05
Press
UP/DOWN
to select
Receiver 2
Pilot Tone
ON/OFF
Hold MENU and
press UP
momentarily
Hold MENU and
press DOWN
momentarily
9V 9V 9V 9V
IMPORTANT:
FREQ.
WARNING
Performance will be degraded if
Receiver 1 is set 4.2 to 4.8 MHz higher
than Receiver 2. The LCD will also flash
this message periodically.
Receiver 2 should always be set to a higher frequency
than Receiver 1 by at least 400 kHz (four standard steps).
Navigating the LCD
NOTE: This setting does not
appear when the MIXMODE
is set to DIRECT
NOTE: Press the
BACK button from
the Main Window
to briefly display
the external power
supply voltage.
NOTE: To reset the timer, set the TXBAT
mode to anything other than 9VT or AAT,
then back to the desired mode.