Lectrosonics UMC16b - Manual (Page 6)

UMC16B
LECTROSONICS, INC. 6
Specifications
Type: Active RF distribution system with ceramic filtering
Inputs: Two 50 Ohm BNC jack on rear panel
Third order intercept: +27dBm at input
Outputs:
Type: 16 BNC jacks on rear panel. Eight jacks per antenna.
Isolation: 20 dB min, any output to any output
Any output can be open, shorted, or terminated without
affecting other outputs.
Splitter type: Wilkinson 1/4 wave strip-line
Filter passband: UMC16B: 537 to 768 MHz (blocks 21 to 29)
UMC16BL: 470 to 692 MHz (blocks 470 to 26)
(See serial number sticker on side panel for frequency
range of your particular unit.)
Input/Output RF gain: 0 dB nominal
In-Band Ripple: +/-2 dB
Power Requirements: 12 to 16 VDC; overload protection provided by internal auto
resetting poly fuse
Power consumption: Nominally 300 mA at 15V DC
Dimensions: 19 x 7 x 1.75 inches
Weight: 2 lbs., 9ozs.
Specifications subject to change without notice.
Service and Repair
If your system malfunctions, you should attempt to
correct or isolate the trouble before concluding that the
equipment needs repair. Make sure you have followed
the setup procedure and operating instructions. Check
the inter-connecting cords.
We strongly recommend that you do not try to repair
the equipment yourself and do not have the local repair
shop attempt anything other than the simplest repair. If
the repair is more complicated than a broken wire or
loose connection, send the unit to the factory for repair
and service. Don’t attempt to adjust any controls inside
the units. Once set at the factory, the various controls
and trimmers do not drift with age or vibration and never
require readjustment. There are no adjustments inside
that will make a malfunctioning unit start working.
LECTROSONICS service department is equipped and
staffed to quickly repair your equipment. In-warranty
repairs are made at no charge in accordance with
the terms of the warranty. Out of warranty repairs are
charged at a modest flat rate plus parts and shipping.
Since it takes almost as much time and effort to deter-
mine what is wrong as it does to make the repair, there
is a charge for an exact quotation. We will be happy to
quote approximate charges by phone for out of warranty
repairs.
Returning Units for Repair
You will save yourself time and trouble if you will follow
the steps below:
A. DO NOT return equipment to the factory for repair
without first contacting us by letter or by phone.
We need to know the nature of the problem, the
model number and the serial number of the equip-
ment. We also need a phone number where you
can be reached 8 am to 4 pm (Mountain Standard
Time).
B. After receiving your request, we will issue you a
return authorization number (R.A.). This number
will help speed your repair through our receiving
and repair departments. The return authorization
number must be clearly shown on the outside of
the shipping container.
C. Pack the equipment carefully and ship to us, ship-
ping costs prepaid. If necessary, we can provide
you with the proper packing materials. UPS is
usually the best way to ship the units. Heavy units
should be “double-boxed” for safe transport.
D. We also strongly recommend that you insure the
equipment, since we cannot be responsible for
loss of or damage to equipment that you ship. Of
course, we insure the equipment when we ship it
back to you.
Mailing Address:
Lectrosonics, Inc.
PO Box 15900
Rio Rancho, NM 87124 USA
Shipping Address:
Lectrosonics, Inc.
581 Laser Road
Rio Rancho, NM 87124 USA
Telephone:
TEL: (505) 892-4501 or
(800) 821-1121
FAX: (505) 892-6243
Web: http://www.lectrosonics.com
E-mail: [email protected]
Repair e-mail: [email protected]