Lectrosonics QUADUHFD - Manual (Page 5)

Multi-channel Wireless System
REAR PANEL DESCRIPTION
SERIAL/FREQUENCY LABEL - This label, located on the rear of the housing on each distribution module, indicates
the serial number and the RF passband of the distribution module. IMPORTANT - The receivers installed in the unit
must fall between the passband indicated on the label. Serious signal loss results if the receiver frequencies are
outside the RF passband.
POWER XLR CONNECTOR - This 4 pin Switchcraft D4M connector is the power input jack for both the AC charger
and for external 12VDC power. Pins 1 and 4 are used for external 12 VDC input. Pins 2 and 3 are utilized for 15VDC
charging with the CH80 charger.
POLARITY DIAGRAM - The polarity diagram on the lower panel indicates the wiring connections for the 4 pin XLR
power connector. Use this diagram when connecting your own external power source to the system.
POWER LEADS - These connectors provide power for the individual receivers. Insert the connectors into the jack
provided on each receiver.
INSTALLATION SCREWS - The two large counter-sunk phillips head screws in the central area between the receiv­
ers are used for receiver installation and removal. See the following page for further instructions.
RECEIVER AUDIO OUTPUT - Supplies a balanced, low impedance output at microphone or line level. The audio
signal is output on pins 2 and 3, while pin 1 is ground. The output level of this jack is controlled by the OUTPUT
control on the front panel of the receiver and by the range switches in the battery compartments of the receivers (see
receiver instruction manuals). The connector is a standard XLR type.
RECEIVER POWER IN JACK - Connects to the POWER LEAD for powering the receiver from the QUADUHFD
source.
Installation Receiver Audio Receiver
Screws
mful does not caus
device condition that t
ubj Oper
Part
Output Power In Jack
Power XLR
Connector
Polarity
Diagram
1
2
3
4
EXTERNAL POWER JACK
PIN 1:
PIN 2:
PIN 3:
PIN 4: External Power Ground
CH-80 Charger Ground
CH-80 Charger (+)
Ext Pwr, +12 to 16 VDC, 0.6 to 2 Amps
581 Laser RD, Rio Rancho, NM 87124
CHARGING THE INTERNAL GEL-CEL PACK:
Insert CH-80 charger plug into jack on distribution
module rear panel. Charge until green “charging”
LED goes out or longer. Prolonged charging will
not harm the batteries.
(800) 821-1121 (505) 892-4501
TIGHTEN THESE SCREWS LAST
AFTER INSTALLING THE RECEIVERS
http://www.lectrosonics.com
LECTROSONICS, INC.
1:
2:
3:
4: External Power (–)
CH-80 Charger (–)
CH-80 Charger (+)
External Power (+),
12 to 16 VDC,
0.6 to 2 Amps
UHF RF/POWER
DISTRIBUTION
1
2
3
4
POWER
INPUT
UHF RF
DISTRIBUTION
1 2
3
This device complies with
Part 15B of the FCC Rules.
Operation is subject to the
1 2 1 2
condition that this device
does not cause harmful
interference.
FCC ID: DBZUCR195
Lectrosonics, Inc.
Made in USA 1 2
3
Th complies with
the FCC Rules.
i to the
interferenc .
FCC ID: DBZUCR195
Lectrosonics, Inc.
Made in USA
3
This device complies with
3 Part 15B of the FCC Rules.
Operation is subject to the Part 15B of the FCC Rules.
condition that this device
does not cause harmful condition that this device
interference.
FCC ID: DBZUCR195
interference.
Lectrosonics, Inc.
Made in USA
Lectrosonics, Inc.
Made in USA
This device complies with
Operation is subject to the
does not cause harmful
FCC ID: DBZUCR195
To
Battery
Rio Rancho, NM – USA 5