MIDLAND G8 E BT - Manual (Page 18)

16
For.a.different.use,.both.possibilities.can.be.chosen..The.internal.mike.of.the.
radio.will.be.deactivated.as.soon.as.the.Bluetooth.link.is.established..
Volume setting
The.volume.on.the.Bluetooth.headset.can.be.adjusted.by.its.button.or.by.the.
volume.knob.of.the.radio.
attention: when the Bluetooth is enabled, the radio’s speaker will be
excluded and the volume is adjusted on the Bluetooth.
Trouble Shooting:
Bluetooth Connection interrupted or not possible
If. the. communication. link. is. interrupted. or. not. possible,. please. try. first. to.
switch.both.units.off,.wait.some.seconds.and.then.switch.on.again..Press.the.
BT button.and.check.whether.or.not.the.link.is.re-established..If.this.procedure.
does.not.help,.please.repeat.the.pairing.procedure..However,.it.can.happen.
that.2.devices.may.lose.their.pairing,.maybe.through.EMC.or.radio.interfer-
ence.effects.
note:
When connecting the
G8E-BT with BTSKi /BTEVa /BTCiTY, please note that
the communication link is switched on by long pressing (3 sec.) the central
“ Control” button on the headset.
In case you are using a BT1, the communication audio will be enabled by
briefly pressing the “ Phone” key of the headset.
BT2: if your G8E-BT has been paired to the “Phone” key of your BT2, just
press such key to switch on the audio; otherwise, if the transceiver has been
paired to the “ aUX” key, it is not necessary to press any button as the com-
munication audio is already on.
“MENU” key
The.following.features.can.be.selected.by.using.the. “menu” button:
.› Channel.selection
.› CTCSS.tone.setting
.› DCS.tone.setting.
.› High/low.power.selection.
.› VOX.
.› Vibracall.function
.› Call.melodies
.› Roger.Beep
.› Keypad.Beep
.› Dual.Watch.function
.› Out.of.Range
CTCSS/DCS tone setting
CTCSS.and.DCS.tones.are.similar.to.access.codes.and.enable.the.radio.to.
communicate.only.with.the.users.that.are.tuned.on.the.same.channel.and.
have.set.the.same.code..For.each.channel,.you.can.set.up.to.38.CTCSS.and.
104.DCS.tones..
These.tones.can.be.set.only.on.the.8.main.PMR446.channels.(from.P1.to.P8)..
The.pre-set.channels.from.9p.to.24p.cannot.be.modified.
Activating the CTCSS tones:
1..Turn.on.the.unit..
2..Select.the.desired.channel.by.pushing.the. MENU.button.and.the.▲▼.chan-
nels.
3..Press.the. MENU.button.till.the.display.shows.CTC.and.the.CTCSS.tone.
blinks.on.the.right.(“of”=.no.code.–.default.condition).
4..Select.the.desired.CTCSS.tone.by.pushing.▲▼ .
5..To.confirm.the.setting,.push. PTT or.wait.for.5.seconds.
Deactivating the CTCSS tones:
If.you.don’t.want.to.use.the.CTCSS.tones,.follow.these.steps:
1..Select.the.desired.channel
2..Press. the. MENU.key.till.the.display.shows.the.CTCSS.tone.blinking.on.
the.left;
3..Select.“ of”.by.means.of.▲▼.
Activating the DCS codes:
1..Turn.on.the.unit..
2..Select.the.desired.channel.by.pressing.MENU.and.▲▼.keys .
3..Push.the. MENU.button.again.till.the.display.shows.DCS.and.the.tone.code.
blinks.on.the.right.(“of”=no.code.–.default.condition).
4..Select.the.desired.DCS.code.by.pushing.▲▼ .
5..To.confirm.the.setting,.press.the. PTT or.wait.for.5.seconds.
Deactivating the DCS codes:
1..Select.the.desired.channel...
2..Press.the. MENU key.till.the.display.shows.the.channel.in.use.and.the.DCS.
code.blinks.on.the.right.
3..Select.“ of”.by.pushing.▲▼.
Hi/low power selection
To.select.the.power.level,.press.the. MENU button.till.the.display.shows.Pr.
Use.▲▼.to.select. L (low.power).or.H (high.power)..To.confirm.your.selection,.
push. PTT or wait.for.5.seconds..
When.the.batteries.are.fully.charged,.the.high.power.is.500.mW.(ERP),.while.