Altec Lansing inMotion Portable Speaker Docking Station - Manual (Page 4)

2
Thank you for purchasing this Altec Lansing product. For generations, Altec
Lansing has been first in audio innovation. Today, our line of powered
speakers has received more performance awards than any other brand. In
all kinds of desktop environments, in every price range, Altec Lansing offers
sound of distinction — giving even the most demanding customers the
audio enjoyment they seek. Just listen to this!
Box Contents
• inMotion portable audio system
• Universal Power Supply
• 3.5mm Stereo Cable
• Protective Case
• 10GB/15GB iPod Docking Spacer
• Docking Connector Travel Cover
• Manual
• Quick Connect Card (may be located on internal box flaps)
Placing the inMotion system
Position the inMotion system on a level surface preferably close to you
(within three feet). The inMotion system can be placed close to video
displays such as TVs and computer monitors without distorting the image.
Making Connections
Warning: Do not insert the speaker system’s universal power supply into a
wall outlet until all connections are made. Also, turn off your iPod before
docking on the inMotion system.
To ensure first-time operation as expected, please carefully follow the
connection sequences described below in the order indicated.
Newer iPods can be connected to the inMotion system via the docking port,
while older iPods must be connected using the auxiliary input jack. These
are the only signal input connections that need to be made. After either of
these connections are made, insert the barrel connector from the universal
power supply into the connector marked
on the rear of the
inMotion system. After this connection is made, insert the universal power
supply into a wall outlet. You can now use your speakers.
Please note, the inMotion system can also be powered with four AA
batteries (not included). Make sure the batteries are installed as illustrated
in the battery compartments found on the bottom of the inMotion system.
Headphones
To use headphones with the system, plug them into the jack labeled
on the rear of the inMotion system. When headphones are connected, all
external speakers are muted.
Powering On
AC Power
After your iPod is docked on the inMotion system, plug the universal power
supply into a wall outlet. The speaker system is now ready to operate.
1. Turn on your iPod
2. Turn on the Altec Lansing inMotion system by sliding the power switch
located on the front panel to the right. A green LED will light next to
the switch when the power is on.
Note: To avoid hearing a popping sound when you turn on your Altec
Lansing speaker system, always turn on your audio source first.
DC (Battery) Power
Install four AA batteries (not included) into the battery compartments on
the bottom of the inMotion system (two to each compartment). Make sure
the batteries are installed as illustrated in the battery compartments. After
your iPod is docked on the inMotion system, the speaker system is ready
to operate.
1. Turn on your iPod
2. Turn on the Altec Lansing inMotion system by sliding the power switch
located on the front panel to the right. A green LED will light next to
the button when the power is on. The LED will turn amber in color to
indicate the batteries must be replaced.
Note: To avoid hearing a popping sound when you turn on your Altec
Lansing speaker system, always turn on your audio source first.
Volume
The buttons on the front of the inMotion system are the master
volume controls for the speaker system. Press and hold the “+” button to
increase the volume and the “–” button to decrease the volume.
IN
M
OTION
Portable Audio System
Total Continuous Power: 4 Watts RMS
• Front Speakers: 2 Watts/channel @ 8 ohms
@ 10% THD+N @ 20 – 20 kHz
2 Channels Loaded
Frequency Response: 60 Hz – 20kHz
Signal to Noise Ratio
@ 1 kHz input:
> 75 dB
Drivers: Four 1" full-range
neodymium microdrivers
POWER REQUIREMENTS
USA, Canada and applicable
Latin American countries:
120 V AC @ 60 Hz
Europe, United Kingdom,
applicable Asian countries,
Argentina, Chile and Uruguay:
230 V AC @ 50 Hz
ETL/cETL/CE/NOM/IRAM Approved
System Specifications
Altec Lansing’s superior sound comes from our patented technology, which utilizes custom-built, high-fidelity drivers, state-of-the-art equalization circuitry,
and a harmonious mix of the following specifications: