Blagdon Pump B10 Non-Metallic - Manual (Page 3)

Page 6
Parts List
Item Description Qty. Standard: Polypropylene
1 Centre Section 1 E801A
2 Valve Gasket 1 E800J
AIR VALVE
ASSEMBLY
E800
(items 2 - 10)
3 Valve Insert 1 E500H
4 Air Diverter 1 10-075
5 End Cap 2 E800D
6 End Cap O-Ring 2 E500E
7 Valve Screw 4 10-050
8 Valve Body 1 10-048
9 Valve Spool 1 E500B
10 Valve Spool U-Cup 2 P98-104A
11 Main & Pilot Shaft O-Ring 8 E503B
PILOT VALVE
ASSEMBLY
12 Pilot Shaft Spacer 5 E503C
13 Shaft Retainer 2 E801B
14 Pilot Shaft 1 E803A
15 Pilot Shaft Snap Ring 2 E503D
16 Shaft Retainer Screw 4 E501C
POLY / SANTOPRENE PUMPS KYNAR / PTFE PUMPS
17 Valve Seat 4 10-022(Poly) 10-039(Kynar)
18 Spring 4 10-030 10-030
19 Valve Stem 4 10-005 10-038
20 Valve Seat Seal 8 10-073
Santoprene Option
10-045
PTFE Option
21 Water Chamber Bolt (Short) 12 10-051 10-051
22 Water Chamber Bolt (Long) 4 10-052 10-052
23 Water Chamber 2 10-002 10-036
24 Foot Pad 4 10-035 10-035
25 Outer Diaphragm Plate 2 10-023(poly) 10-023(poly)
10-040(kynar) 10-040(kynar)
26 Diaphragm 2 10-032(R) 10-044
27 Inner Diaphragm Plate 2 C126 C126
28 Main Shaft 1 10-028 10-028
29 Manifold 2 10-003 10-037
30 Muffler 1 06-034 06-034
Page 3
Before pump operation, inspect all
gasketed fasteners for looseness caused
by gasket creep. Re-torque loose
fasteners to prevent leakage. Follow recommended
torques stated in this manual.
CAUTION!
Before doing any maintenance on the
pump, be certain all pressure is completely
vented from the pump, suction, discharge,
piping, and all other openings and connections. Be
certain the air supply is locked out or made
non-operational, so that it cannot be started while work
is being done on the pump. Be certain that approved eye
protection and protective clothing are worn all times in
the vicinity of the pump. Failure to follow these
recommendations may result in serious injury or death.
WARNING!
In the event of diaphragm rupture, pumped
material may enter the air end of the
pump, and be discharged into the atmos-
phere. If pumping a product which is hazardous or toxic,
the air exhaust must be piped to an appropriate area for
safe disposition.
WARNING!
Airborne particles and loud noise hazards.
Wear ear and eye protection.
WARNING!
RECYCLING
Many components of BLAGDON air
operated double diaphragm pumps are
made of recyclable materials. We
encourage pump users to recycle worn out parts and
pumps whenever possible, after any hazardous pumped
fluids are thoroughly flushed.
TYPICAL ORDER CODE = B10. 01. P P. R P P
WETTED COMPONENTS
P : POLYPROPYLENE
K : PVDF (KYNAR)
NON - WETTED COMPONENTS
P : POLYPROPYLENE
VALVE SEATS
P : POLYPROPYLENE
K : PVDF (KYNAR)
VALVE STEMS
P : POLYPROPYLENE
K : PVDF (KYNAR
DIAPHRAGMS
R : SANTOPRENE
T : PTFE
DESIGN LEVEL
MODEL - B10
ITEM DESCRIPTION QTY PART NUMBER
2 VALVE GASKET 1 E800J
3 VALVE INSERT 1 E500H
4 AIR DIVERTER 1 10-075
6 END CAP O-RING 2 E500E
10 VALVE SPOOL U-CUP 2 P98-104A
11 PILOT SHAFT O-RING 6 E503B
11 MAIN SHAFT O-RING 2 E503B
ASK1001P - AIR SIDE KIT WETTED END KITS
PART NO. DESCRIPTION
SA10RPP POLY./SANTOPRENE
SA10TPP POLY./PTFE
SA10RKK KYNAR/SANT.
SA10TKK KYNAR/PTFE
SPARES KITS :- REFER TO TABLE & DRAWING ON PAGES 4,5 & 6
Note. These descriptions refer to the Pump body
and Diaphragm materials.