Staub Electronics SM-PROJ-M-BLK STRONG - UNIVERSAL PROJECTOR MOUNT FOR PROJECTORS UP TO 30LBS - Manual (Page 2)

ASSEMBLY INSTRUCTIONS
SPECIFICATIONS
• Maximum load: 30 lbs.
• Tilt range: +/- 70°
• Horizontal rotation: 360°
WARNINGS
1. Make sure these instructions are read and thoroughly understood
before attempting installation. If you are unsure of any part of the
installation process, contact a professional installer for assistance.
2. The wall or mounting surface must be capable of supporting the
combined weight of the mount and the display; otherwise the
structure must be reinforced.
3. Safety gear and proper tools must be used. Failure to do so can result
in property damage and/or serious injury.
4. Follow all instructions and recommendations regarding adequate
ventilation and suitable locations for mounting your display. Consult
the owner‘s manual for your display for more information.
TOOLS REQUIRED
• Phillips Head Screw Driver
• Electric or Portable Drill
• 3/16” (5 mm) Drill Bit and Stud Finder for Drywall Installation
• 5/16” (8 mm) Masonry Bit for Concrete Installation
INSTALLATION
Step 1 - Installing The Ceiling Plate
Attach the Ceiling Plate (N) to the ceiling
using the Wood Screws (A). If you are installing
into a concrete ceiling, also use the Concrete
Anchors (B).
Step 2 - Installing the Mount Body
Screw the Mount Body (Q) onto the Ceiling
Plate (N) by turning it clockwise. Tighten the
set screw(s) using the Allen Key (E).
Step 3 - Attaching the Mount Arms to the Mount Base
Secure the Mount Arms (O) to the Mount Base (M)
using the Arm Screws (C) and Washers (L). Leave
the Arm Screws (C) loose so that you can adjust
them when attaching the projector.
Step 4 - Attaching the Mount Arm Assembly to the Projector
Attach your projector to the Mount Arms (O) using the
correct screw from the hardware kit (F, G, H, I, J, or K).
If none of these screws fit, check with the manufacturer
of your projector for the proper size. Depending on
the surface of the projector, you may want to use
spacers (P) between arm and projector. Once
attached, make sure all screws are tight.
Step 5 - Attaching the Projector to the Mount Body
Carefully hook the Mount Base (M) with your projector
attached to the Mount Body (Q). Tighten the Allen
Screws on all four sides of the Mount Base (M) with
Allen Key (D) to prevent the projector from being
knocked off the Mount Body (Q).
Installation is now complete.
Hint: Using both Allen Keys (D), one on each side,
will help with consistent tightening.
BOX CONTENTS
• Wall mount
• Instruction manual
• Hardware kit
PACKAGE CONTENTS
(A) Wood screw x2 (F) M4 x 16 Screw x4
(G) M4 x 30 Screw x4
(K) M6 x 30 Screw x4
(L) Washer x4 (P) 6mm Spacer x4
(M) Mount Base x1
(N) Ceiling Plate x1
(Q) Mount Body x1
(O) Mount Arm x4
(I) M5 x 30 Screw x4
(H) M5 x 16 Screw x4
(J) M6 x 16 Screw x4
(B) Concrete Anchor x2
(D) 6mm Allen Key x2
(E) 3mm Allen Key
(C) Arm Screw x4
(N)
(A) (A)
(E)
(N)
(Q)
(C) (M)
(O)
(D)
(Q)
(M)
(Q)
(L)
Swivel
Screw
Tilt Adjustment Screws
CAUTION: This wall mount is intended for
use only with the maximum weight of 30 lbs