Sunex Tools 5218 - Manual (Page 4)

5218 4 rev. 12/31/04
MAINTENANCE AND INSPECTION
1. Inspect the crane before each use. Check for cracks in the
jack support, boom and boom extension. Check for loose,
missing or damaged parts and for hydraulic oil leaks. If the
crane is damaged in any way, it should be removed from
service immediately.
2. Check for unauthorized modification of the product.
Modifications to this product and/or use of unapproved
attachments are prohibited due to the potential hazards
that are associated with improper use.
3. Any crane which appears to be damaged in any way,
found to be worn, or operates abnormally MUST BE
REMOVED FROM SERVICE UNTIL REPAIRED. Owners
and/or operators should be aware that repair of the equip-
ment requires specialized knowledge and facilities. Only
factory authorized parts, labels and decals shall be used on
this equipment.
4. If jack is subjected to abnormal load or shock, remove
from service and have it examined by an Authorized
Repair Service.
5. Clean all surfaces and maintain all labels and warnings.
6. Grease Pivot Points:
A. Boom to Upright Support Post
B. Ram Mount to Boom
A list of authorized repair facilities is available from the
manufacturer.
CHECK OIL LEVEL
WARNING
Always purchase those products labeled “Hydraulic Jack Oil”.
Do not use brake or transmission fluids, as they can damage
the seals.
1. Turn release valve counterclockwise to allow ram to
fully retract.
2. Remove fill plug.
3. With jack in vertical position, proper oil level should be
even with bottom of hole. If low, fill with NEW, clean
hydraulic jack oil and recheck level. Do not overfill!!
4. Replace filler plug.
5. Turn release valve counterclockwise one full turn to open
and allow lift arm to retract.
6. Close release valve and check for proper pump action. It
may be necessary to perform the above move more than
once to assure air is evacuated totally.
STORAGE
1. Lower the boom (25) to its lowest position, with the boom
extension (26) slid into position #4. Ensure pin (24) is
installed and secured with clip (8).
2. Remove clips and pins (3, 8) holding front legs (1, 2) to the
base (7). Remove front legs from base and position them
vertically in the storage pockets located slightly to the rear
of the wheels (30) on base.
3. Reinstall the clips and pins removed in step 2 to prevent
the loss of parts.
LIMITED WARRANTY:
SUNEX INTERNATIONAL, INC. WARRANTS TO ITS CUSTOMERS THAT THE COMPANY’S SUNEX TOOLS ® BRANDED PRODUCTS
ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will repair or replace its Sunex Tools
® branded products which fail to give satisfactory service due to
defective workmanship or materials, based upon the terms and conditions of the following described warranty plans attributed
to that specific product.
This product carries a ONE-YEAR warranty. During this warranty period, Sunex Tools will repair or replace at our option any part
or unit which proves to be defective in material or workmanship.
Other important warranty information...
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover
any repairs or replacement made by anyone other than Sunex Tools or its authorized warranty service centers.
The foregoing obligation is Sunex Tools’ sole liability under this or any implied warranty and under no circumstances shall we
be liable for any incidental or consequential damages.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
Return equipment or parts to Sunex Tools, transportation prepaid. Be certain to include your name and address, evidence of the
purchase date, and description of the suspected defect.
If you have any questions about warranty service, please write to Sunex Tools. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state.
Repair kits and replacement parts are available for many of Sunex Tools products regardless of whether or not the product is
still covered by a warranty plan.
SHIPPING ADDRESS:
Sunex Tools
315 Hawkins Rd.
Travelers Rest, South Carolina 29690 MAILING ADDRESS:
Sunex Tools
P.O. Box 4215
Greenville, South Carolina 29608