Volt meter fluke model 87 or equivalent – System Sensor D4120, D4P120, and D4S User Manual
Page 4
[8] FIELD WIRING INSTALLATION GUIDELINES
All wiring must be installed in compliance with the National Electrical Code
and the local codes having jurisdiction. Proper wire gauges should be used.
The conductors used to connect smoke detectors to control panels and acces-
sory devices should be color-coded to prevent wiring mistakes. Improper con-
nections can prevent a system from responding properly in the event of a fire.
For signal wiring, (wiring between interconnected detectors or from detectors
to auxiliary devices), it is recommended that single conductor wire be no
smaller than 18 gauge.
Smoke detectors and alarm system control panels have specifications for al-
lowable loop resistance. Consult the control panel manufacturer’s specifica-
tions for the total loop resistance allowed for the particular control panel being
used before wiring the detector loop.
[8.1] WIRING INSTRUCTIONS
The D4120 and D4P120 detectors are designed for easy wiring. The housing
provides a terminal strip with clamping plates. The D4S housing provides 4
wiring terminals with clamping plates. Wiring connections are made by slid-
ing the bare end of the wire under the plate, and tightening the clamping plate
screw. See Figure 7 on page 5 for system wiring.
[8.2] SENSOR 2 INSTALLATION/WIRING
The power board is capable of controlling a second housed sensor. The second
sensor, model D4S, can be wired to the power board per the following:
1. Connect wires to the four wire terminals in the corner of the D4S sensor
housing designated as Tamper (Y,Y), +R, and –B. Route wires through the
conduit openings in the sensor housing and D4120 power board housing.
2. Connect the opposing ends of the wires to the terminal connections
marked “Sensor 2” on the Power board. See Figure 6 for reference. En-
sure that wires are connected to the appropriate terminal locations. A
No. 0 or 1 phillips screwdriver should be used for terminal connection.
The tamper terminals are not polarity sensitive.
3. Adjust the middle dip switch on the power board to indicate (2) sensors
as shown in Figure 6.
4. The D4S can only be used with new InnovairFlex models and is not com-
patible with previously sold detectors.[9] Unit Configuration:
[9] UNIT CONFIGURATION
A three position Dip Switch is included only on the D4P120 in order to con-
figure the setup of the unit. One switch is used to determine it there are one
or two sensors connected to the Power Board. The second switch selects an
instantaneous or 7-minute tamper Delay. A tamper Condition indicates that
the cover of the sesor Housing has been removed or has not been secured
properly. The third switch is used to turn the Shutdown On Trouble feature
on or off. With this feature turned On, the Aux relay will switch states when
a Trouble Condition occurs.
*Trouble is indicated when the Supervisory Relay, switches state-Termi-
nals 3 and 14 are open in a Trouble Condition
Causes of a Trouble Condition may be:
• Unit loses Power
• Cover Tamper Feature times out
• Wiring Problems between the Sensor and the Power Board
• Mismatch between number of sensors connected to the Power Board and
the Dipswitch setting
HIGH
LOW
9 VOLT
BATTERY
9 VOLT
BATTERY
9 VOLT
BATTERY
TO SAMPLING TUBE
TO EXHAUST TUBE
DIFFERENTIAL
PRESSURE
TRANSMITTER
MODEL #607-01
15 TO 36
VDC SUPPLY
1000 OHM 5%
1 WATT RESISTOR
VOLT METER FLUKE
MODEL 87 OR
EQUIVALENT
+
–
FIGURE 5. PROCEDURE FOR VERIFYING AIR FLOW LESS THAN 500 FPM:
H0163-01
SS-300-000
4 I56-2967-006R
FIELD SELECTABLE
DIP SWITCHES
TEST/RESET
BUTTON
POWER
BOARD LED 2
SENSOR
LEDs
GROUND
SCREW
SENSOR #1
TERMINALS
D4120
CO-LOCATED
WIRING TERMINALS
24V
AC
/DC,
10
24V
AC
/DC,
9
AU
X OUT +,
19
AU
X OUT -,
20
INT/
AU
X-
, 1
INT+
, 12
ALARM,
15
R
TEST
, 11
R RESET
, 2
AC
C
-
AC
C
+
120 VAC
B
-
R
+
Y
Y
B
-
R
+
Y
Y
TAMPER
TAMPER
SENSOR 1
SENSOR 2
OFF/ON
TRBL SHUTDN
1/2 SENSORS
7/0 MIN
TMPR DEL
AY
7,
NO
18
, C
AUX B
8,
NC
17
, NO
AUX A
6,
C
16
, NC
14
, N0
3,
C
13
, NC
5,
NO
SUP
ALARM
4,
C
D4S
SENSOR ONLY
SENSOR #2
TERMINALS
TAMPER
Y Y R B
Y Y R B
+ –
TAMPER
+ –
SENSOR 2
D4120
D4S
NOTE: IF USING (2) D4S
SENSOR ONLY
COMPONENTS WITH
MODEL D4P120 POWER
BOARD COMPONENT, USE
SENSOR #1 TERMINALS
AND WIRE IN SAME
MANNER AS SHOWN FOR
SENSOR #2.
POWER
BOARD LED 1
120
VAC INPUT
24 VAC/
DC INPUT
24V AC/DC, 10
24V AC/DC, 9
AUX OUT +, 19
AUX OUT -, 20
INT/AUX-, 1
INT+, 12
ALARM, 15
R TEST, 11
R RESET, 2
ACC -
ACC +
7, NO
18, C
8, NC
17, NO
6, C
16, NC
14, N0
3, C
13, NC
5, NO
4, C
H0557-14
FIGURE 6. OPTIONAL SENSOR 2 CONFIGURATION AND WIRING: