Qualcraft Cyclone HUV Harness User Manual
Page 4
WARNING!
I
I
f
f
i
i
n
n
s
s
p
p
e
e
c
c
t
t
i
i
o
o
n
n
r
r
e
e
v
v
e
e
a
a
l
l
s
s
a
a
n
n
u
u
n
n
s
s
a
a
f
f
e
e
o
o
r
r
d
d
e
e
f
f
e
e
c
c
t
t
i
i
v
v
e
e
c
c
o
o
n
n
d
d
i
i
t
t
i
i
o
o
n
n
,
,
r
r
e
e
m
m
o
o
v
v
e
e
t
t
h
h
e
e
p
p
r
r
o
o
d
d
u
u
c
c
t
t
f
f
r
r
o
o
m
m
s
s
e
e
r
r
v
v
i
i
c
c
e
e
a
a
n
n
d
d
d
d
e
e
s
s
t
t
r
r
o
o
y
y
i
i
t
t
i
i
m
m
m
m
e
e
d
d
i
i
a
a
t
t
e
e
l
l
y
y
.
.
WARNING!
PLAN THE FALL PROTECTION SYSTEM:
Before installation plan your system. Consider all factors that will affect your safety during use of this equipment. The following
list gives important points to consider when planning your system:
Anchorage: Select a rigid anchorage capable of supporting the loads no less than 5,000 lbs. per worker attached.
Sharp Edges: Avoid working where system components may be in contact with, or abrade against, unprotected sharp edges.
After a Fall: Components which have been subjected to the forces of arresting a fall must be removed from service and
destroyed.
Rescue: The employer must have a rescue plan when using this equipment. The employer must have the ability to perform a
rescue quickly and safely.
ANCHORAGE STRENGTH REQUIREMENT:
The anchorage strength required is dependent on the application. Following are anchorage strength requirements for specific
applications. Ensure that any anchorage point used in a personal fall protection system meet the following requirements.
• Fall Arrest: The structure to which the anchorage connector is attached must sustain static loads applied in the directions
permitted by the fall arrest system of at least 3,600lbs. with certification of a qualified person, or 5,000lbs. without
certification. Refer to OSHA and ANSI for specific definition. This anchor is to be used by one worker only. Do not tie off
equipment. Anchorages used for attachment of a personal fall arrest system shall be independent of any anchorage being
used to support or suspend platforms.
• Restraint: The structure to which the anchor point is attached must sustain static loads applied in the directions permitted by
the restraint system of at least 3,000lbs. When more than one restraint system is attached to an anchorage, the strengths
stated above must be multiplied by the number of restraint system attached to the anchorage.
• Work Positioning: The structure to which the anchor point is attached must sustain static loads applied in the directions
permitted by the work positioning system of at least 3,000lbs., or twice the potential impact load, whichever is greater. When
more than one work positioning system is attached to an anchorage, the strengths stated above must be multiplied by the
number of work positioning systems attached to the anchorage.
INSPECTION OF GUARDIAN HARNESSES:
• Before each use of this equipment inspect it according to the following guidelines:
A formal inspection of fall protection products/components must be performed at least every six months by a competent
person other than the user. The frequency of formal inspections should be based on conditions of use or exposure. Record
the inspection results in the inspection and maintenance log at the end of this manual.
Inspecting the Harness:
Step 1: Inspect harness components for damage, distortion, cracks, worn parts, corrosion, or wear that might affect integrity.
Step 2: Inspect webbing components for cuts, broken fibers, tears, abrasions, mold, burns, or discoloration. Inspect stitching
for possible breaks and identify any load indicators that might have deployed to indicate a fall. Some harnesses feature
webbing that is protected by material sheaths or coverings. These coverings should be folded back and the webbing
underneath checked for integrity.
Step 3: Inspect webbing retainers, buckles, grommets, and plastic web excess keepers for integrity and function.
Step 4: Inspect labels for legibility. If there is no label attached, contact manufacturer.
Step 5: Inspect impact indicators (if present on back of harness) to determine if product has been impacted in a fall. The
indicator will expose threads and a written warning on the tag will be visible if the product has been involved in a fall. If the
impact indicator has been deployed, remove the product from service.
Step 6: Inspect the system components according to the manufacturer’s instructions.
Step 7: Record the inspection results in the inspection log at the end of this manual.