Davey EcoSpa Salt Water Spa Sanitisation System - Manual (Page 4)

4 9
ECO-SPA TM INSTALLATION INSTRUCTIONS
(Refer to diagram next page)
1. Please ensure the EcoSpa™ Control Unit is mounted a minimum of 3 metres
away from the spa water and 1.5 metres above ground level. For a portable
spa, the EcoSpa™ unit can be fitted on the inside of the spa surround, please
ensure easy access.
2. Select mounting point and mark 2 holes 18mm apart. (If the unit is to be
mounted to a brick or concrete wall use a masonry drill bit. Some walls such
as limestone or cement render can damage aluminium, if in doubt seal the wall
before mounting the control unit). Drill the 2 holes and fix suitable screws to
each hole. Recommended screws are 8 gauge.
3. Hang unit via slots in the top rear section of EcoSpa™ unit. NB: The additional
mounting hole at the base of the EcoSpa™ can be used to help secure the unit.
4. Plug power plug from control unit into a suitable weatherproof power outlet.
Ensure appropriate RCD safety device is fitted to mains power. Do not turn
power on until installation is complete. When used with controller, plug into
ozone position and set dip switches H & I to 1.
5. Install Manifold for ORP Sensor Probe and Pressure Switch into spa return
line after the pump.
6. Plumb Electrolytic Cell into spa return line injection housing. Plug Cell
connector into the appropriate receptacle in the bottom of the unit. The Cell can
be installed vertically or horizontally. NOTE: ORP Sensor and pressure switch
MUST be installed prior to the Cell and at least 200mm (8”) from the Cell inlet,
preferably further away.
IMPORTANT NOTICE: For installations where manifold is not used, the pressure
switch must be installed at suitable point on spa return. If return does not
have enough pressure fit the pressure switch between pump return and filter.
The pressure switch should be tapped into a point where the pipe enters a fit-
ting to allow a good thread length. Tap size is 1/8” NPT. Take care not to damage
threaded end and use thread tape for a good seal.
Fit ORP Sensor Probe at least 200mm (8”) before Cell. To fit ORP Sensor Probe
drill hole and tap with a 1/4” BSPF tap. This must be done carefully to ensure a
good threaded fit. Screw the ORP Sensor Probe into the pipework. Note that it is
best to fit the ORP Sensor Probe into a fitting (elbow, coupling, etc) to ensure good
thread length.
7. Connect the pressure switch to the EcoSpa™ Control Unit via the cable
terminated in two insulated pade connectors. Note that the pressure switch is
not waterproof and should not be exposed to the weather.
8. Connect ORP Sensor Probe to socket under EcoSpa™ Control Unit.
* Installation and operating instructions are included with the product when purchased new.
They may also be found on our website.
AUSTRALIA
Davey Support Centre
6 Lakeview Drive,
Scoresby, Australia 3179
Ph: 1300 367 866
Fax: 1300 369 119
Website: davey.com.au
Davey Water Products Pty Ltd
Member of the GUD Group
ABN 18 066 327 517
NEW ZEALAND
Customer Service Centre
7 Rockridge Avenue,
Penrose, Auckland 1061
Ph: 0800 654 333
Fax: 09 527 7654
Website: daveynz.co.nz
® Davey is a registered trademark of Davey Water Products Pty Ltd.
© Davey Water Products Pty Ltd 2012.
Davey ® Repair or Replacement Guarantee
In the unlikely event in Australia or New Zealand that this Davey product develops any malfunction
within warranty periods beginning from the date of original purchase due to faulty materials or
manufacture, Davey will at our option repair or replace it for you free of charge, subject to the
conditions below.
Davey Guarantee Period
Control Box - Two Years Electrolytic Cell - Three Years ORP Probe - Three Years
Should you experience any difficulties with your Davey product, we suggest in the first instance
that you contact the Davey Dealer from which you purchased the Davey product. Alternatively
you can phone our Customer Service line on 1300 367 866 in Australia, or 0800 654 333 in New
Zealand, or send a written letter to Davey at the address listed below. On receipt of your claim,
Davey will seek to resolve your difficulties or, if the product is faulty or defective, advise you on how
to have your Davey product repaired, obtain a replacement or a refund.
Your Davey Guarantee naturally does not cover normal wear or tear, replacement of product
consumables (i.e. mechanical seals, bearings or capacitors), loss or damage resulting from
misuse or negligent handling, improper use for which the product was not designed or advertised,
failure to properly follow the provided installation and operating instructions, failure to carry out
maintenance, corrosive or abrasive water or other liquid, lightning or high voltage spikes, or
unauthorized persons attempting repairs. Where applicable, your Davey product must only be
connected to the voltage shown on the nameplate.
Your Davey Guarantee does not cover freight or any other costs incurred in making a claim.
Please retain your receipt as proof of purchase; you
MUST provide evidence of the date of original
purchase when claiming under the Davey Guarantee.
Davey shall not be liable for any loss of profits or any consequential, indirect or special loss,
damage or injury of any kind whatsoever arising directly or indirectly from Davey products. This
limitation does not apply to any liability of Davey for failure to comply with a consumer guarantee
applicable to your Davey product under the Australian or New Zealand legislation and does not
affect any rights or remedies that may be available to you under the Australian or New Zealand
Consumer Legislation.
In Australia, you are entitled to a replacement or refund for a major failure and for compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure.
Should your Davey product require repair or service after the guarantee period; contact your
nearest Davey Dealer or phone the Davey Support Centre on the number listed below.
For a complete list of Davey Dealers visit our website (davey.com.au) or call: