Rhino Shelter BARN-12W X 20L X 12H - Manual

Assembly Instructions Barn Style 12 x 20 x 12
V1.2
Do NOT Return Assembly To Dealer or Store. For All Assembly Questions or Shortages Please Call MDM Products Directly
Customer Service 800-447-7079 or 203-877-7070
1
s!
ASSEMBLY INSTRUCTIONS
BARN STYLE 12Wx20Lx12H
Congratulation
er
is suggested that you read the assembly instructions
Congratulations on your purchase of a Barn Style
Portable Building by MDM Products LLC. With prop
installation, use, and maintenance, your new unit will
provide many years of good and suitable service. Your
new Rhino Shelter portable enclosure is a combination
of excellent engineering and well thought out design.
The unit is comprised of a rigid tubular frame, covered
with a long life polyethylene cover and double door ends.
The multiple part frame assembly is pre-drilled for easy
insertion of hardware to assemble. The tubing is made
from high-grade galvanized steel tubing, to resist
moisture and oxidation over the life of the shelter. The
covering membrane is made from ASTM-5 approved
polyethylene materials. The cover is also UV protected
for continual exposure to the sunlight.
It
completely before you begin. This will help attain the
best results for your installation.
SAFETY WARNING
The installa form to the tion of this unit must con
requirements of all authorities having jurisdiction in
your specific local area. In the absence of such
requirements, the installation must conform to the
provided assembly and installation instructions.
MDM Products LLC will not be responsible for failure
to comply with any requirements in a given local
area. Consequential damages or injuries caused by
improper installation, alteration, or improper use are
strictly that of the user. Unit MUST be cleared of All
Snow Accumulation immediately to avoid overload.
Unit is not to be used for occupancy for any length
of time. No running internal combustion engines,
open flames, or contact with heated surfaces are
allowed.
e
any’s
CEDURE
For installation assistance or Customer Service, please
call 800-447-7079 or 203-877-7070, 8AM-5PM EST.
Cartons should be inspected upon delivery from carrier,
and any evident damages should be noted on the bill of
lading before signing. If upon opening the cartons
hidden damage is noted, contact carrier or its agent
immediately. Claims for shipping damage MUST be
made with the shipping company. An inspection of th
goods will most likely be required. Do not discard
packing or any components before the freight comp
inspection. All claims for freight damage must be made
with 15 days of receipt of the goods in accordance with
ICC regulations.
SSEMBLY PRO A
ps to install this unit will
roduce a proper and good installation. Failure to read
ventory check before beginning to be
certain all components are available for installation.
unit End Arch, first Interior Arch, and
s Rails and Side
of
osition and level
The proper sequence and ste
p
and follow these guidelines may result in an improper
installation and will void all warranty and protection the
owner is entitled to with the product. The steps to be
undertaken are:
1. Perform an in
2. Prepare location and place unit boxes near location
sight.
3. Assemble six (6) arch assemblies of unit
4. Assemble first
Wind Braces with first Base Cros
Cross Rail sections.
5. Add additional Arch Assemblies with each section
Base Rails, Side rails, and Top Ridge Rails.
6. Place frame into desired p frame
-bolts and drive rod provided.
both end-to-end and side-to-side. Set Corners.
Measure frame feet across and square as needed.
7. Anchor frame assembly to ground with provided
Anchors, u
8. Install two (2) Doors on both ends of frame
assembly.
9. Install Main Cover over frame assembly.
10. Install Roll Up Door Kit to End Door.
TOOLS REQUIRED
The following hand tools are suggested for proper
installation of your new Rhino Shelter unit:
9/16” Open nd Wrench E
9/
VENTORY CHE
16” Socket or Box Wrench
Large Flat Tip Screwdriver
Maul or Sledgehammer
2-foot Level
10-F der oot Step Lad
IN CK
tart installation proced S ure by removing all components
from packaging and ensure all components are present
Item Qty Description
No.
1
8 Interi
2-3/8 or A hts Fem x Male
” Di
rch Straight Uprig
ameter
2 4 End Arch . Uprights with Foot 2-3/8” Dia
3 6 Ridge Be ” Dia. nd – Male x Male 2-3/8
4 12 Ridge Be 3/8” Dia. nd – Male X Female 2-
5 12 Ridge Bend – Female x Female – 2-3/8”