Video Mount Products FP-XMWAB - Manual

IMPORTANT! For safety reasons, the concrete wall must be
capable of supporting the combined weight of the mount and the
display. The manufacturer takes no responsibility for failure caused
by walls of insufficient strength.
1
2
3
4
Set the mount aside and drill a 10
mm (3/8”) hole at each marked
location. Remove any excess dust
from the holes.
Insert a concrete anchor (C) into
each hole so that it is flush with the
concrete surface (see Fig. 4). A
hammer can be used to lightly tap
the anchors into place if necessary.
NOTE: If the concrete wall is covered
by a layer of plaster or drywall, the
concrete anchor must pass
completely through the layer to rest
flush with the concrete surface.
Place the mount against the wall
over the drilled holes, making sure the arrow on the mount
faces upward. Attach the mount to the wall using the lag
bolts (A) and lag bolt washers (B) provided (see Fig. 2). Do
not over-tighten these bolts and do not release the
mount until all bolts are in place. Ensure that the mount
remains level after all bolts are secured.
5
Part 2 – Attaching the Mount Arms to the Display
(continued)
(C) Concrete Anchor (x4)
INSTRUCTION MANUAL
Display Size: 32” to 52”
Maximum Load: 130 lbs
Mounting Pattern: Up to 800 mm x 500 mm
Tilt Range: 0 - 15°
Pan/Swivel Range: 0 - 90°
Profile: 5.3” to 16.3”
Read these instructions before you begin. If you are
unsure of any part of the process, contact a professional
contractor or installer for assistance. Improper installation
can result in injury or damage.
The wall or mounting surface must be capable of
supporting the combined weight of the mount and the
display; if not, the structure must be reinforced.
Locate pipes, wires, or any other hazards in the wall where
you wish to install the mount before drilling.
Safety gear and proper tools must be used. Failure to do so
can result in injury or damage.
A minimum of two people are required for installation. Do
not attempt to install this mount alone under any
circumstances.
Follow all instructions and recommendations regarding
adequate ventilation and suitable locations for mounting
your display. Consult the owner‘s manual for your particular
display for more information.
1
2
3
4
5
6
(A) M8 x 63 Lag Bolt (x4)
(B) Lag Bolt Washer (x4)
(D) M6 x 12 Screw (x4)
(E) M6 x 30 Screw (x4)
IMPORTANT! For safety reasons, this mount must be secured to at
least two wood studs no less than 16” apart. The studs must be
capable of supporting the combined weight of the mount and
display.
3
4
5
SPECIFICATIONS
OPERATION AND ADJUSTMENT
BOX CONTENTS
HARDWARE KIT
TOOLS REQUIRED
INSTALLATION
WARNINGS
WARNINGS (continued)
1
2
A
B
Fig. 2
Phillips Head Screw Driver
Ratchet or Driver with 13 mm (1/2”) Socket
Electric or Portable Drill
6 mm (1/4”) Drill Bit and Stud Finder for Drywall Installation
10 mm (3/8”) Masonry Bit for Concrete Installation
Full-motion Mount (x1)
Mount Arm (x2) Instruction Manual (x1)
Hardware Kit (x1)
Part 1B – Mounting to the Wall (Concrete)
Fig. 3
Fig. 4
NOTE: This mount comes with a selection of different screw
diameters and lengths to accommodate a wide variety of
display models. Not all of the hardware in the kit will be used. If
you cannot find the appropriate screw size in the kit provided,
consult the manufacturer of your display for more information.
Part 2 – Attaching the Mount Arms to the Display
IMPORTANT! Use extra care during this part of the installation. If
possible, avoid placing your display facedown as it may damage
the viewing surface.
Part 1A – Mounting to the Wall (Drywall) (continued)
Part 1B – Mounting to the Wall (Concrete) (continued)
Place the mount against the wall in the desired location
and level it using the integrated bubble level.
While another person holds the mount in place, mark four
locations on the wall for securing the mount to the wall
(see Fig. 3).
Fig. 1
Use a high quality stud finder to locate two adjacent studs
where you wish to install your mount. Mark both edges of
each stud to help identify the exact center.
NOTE: You must use the center of each stud to avoid
cracking or splitting the wood during installation.
Place the mount against the wall and level it using the
integrated bubble level.
While another person holds the mount in position, mark
four locations (two per stud) for securing the mount to the
wall (see Fig. 1).
Set the mount aside and drill a 6 mm (1/4”) pilot hole at
each marked location.
Place the mount against the wall over the drilled holes,
making sure the arrow on the mount faces upward. Attach
the mount to the wall using the lag bolts (A) and lag bolt
washers (B) provided (see Fig. 2). Do not over-tighten
these bolts and do not release the mount until all bolts
are in place. Ensure that the mount remains level after all
bolts are secured.
1
2
Attach the mount arms to the back of your display using
the screws identified in Steps 1 and 2 (see Fig. 5):
A
B
If you are using the M6 screws you will also need to use
the M6 washers (H). M8 screws do not require washers.
If you are using the longer screws on a display with a
curved or recessed back, you may also need to use the
spacers (I). Use one spacer or two spacers stacked as
needed. Only use a spacer if necessary.
NOTE: The mount arms must be attached with the safety
tabs facing outward (i.e. away from the middle of the
display). Otherwise, the safety tabs cannot be accessed (see
Fig. 6).
3
Determine the correct length of screw to use by examining
the back of your display:
If the back of your display is flat and the mounting holes
are flush with the surface, you will use the shorter screws
(D or F) from the hardware kit.
If the back of your display is curved, has a protrusion, or if
the mounting holes are recessed, you will need to use the
longer screws (E or G) and the spacers (I).
Determine the correct diameter of screw to use by carefully
trying one of each size (M6 and M8) from the hardware kit.
Do not force any of the screws – if you feel resistance
stop immediately and try a smaller diameter screw.
Part 3 – Final Assembly
Part 3 – Final Assembly (continued)
1 With the help of another person, carefully lift your
display and place it on the mount. Do not release the
display until the mount arms have securely hooked onto
the mount.
Move the safety tab located on each arm into position
so that it prevents the display from being lifted from the
mount. Insert a safety stopper (J) into each tab to keep it
in place. A padlock (not included) can be used in place
of one of the safety stoppers to help prevent unwanted
removal of the display.
2
IMPORTANT! The safety tabs and stoppers must be used at all
times to prevent the display from being accidentally knocked from
the mount.
3 Cables can be routed through the hooks located on the
mount to keep them organized and out of the way.
2
1 To change the tilt angle of your display, have one person
hold the display firmly in place while another person
loosens the tilt knobs located on each side of the mount.
Once loosened, you may move your display to the desired
position. Re-tighten the tilt knobs to lock the tilt angle in
place. Do not release the display until both tilt knobs are
fully tightened.
Swivel adjustments can be made by grasping the display
firmly and moving it to the desired position. Be careful that
fingers or cables do not get pinched when moving the
mount. If any of the swivel joints are too tight or too loose,
they can be adjusted using the S4 Allen key (K) from the
hardware kit.
Level adjustments can be made by holding the display in
place and loosening the screw located behind the mount
using the S4 Allen key (K) from the hardware kit (see Fig. 7).
Do not fully loosen or remove this screw. Carefully level
your display and re-tighten the screw.
Periodically clean your mount with a dry cloth. Inspect all
screws and hardware at regular intervals to ensure that no
connections have become loose over time. Re-tighten as
needed.
3
4
CAUTION: This wall mount is intended for use only with
the maximum weight of 130 lbs. Use with heavier than
the maximum weights indicated may result in instability
causing possible injury.
FULL MOTION WALL MOUNT
FOR LCD, PLASMA, and LED DISPLAYS
(G) M8 x 30 Screw (x4)
(F) M8 x 12 Screw (x4)
(H) M6 Washer (x4)
(I) Spacer (x8)
(K) S4 Allen Key (x1)
(J) Safety Stopper (x2)
Fig. 7
Fig. 5
For displays with curved
or recessed backs.
For displays with
flat backs.
Fig. 6
Safety Tabs
Safety Tabs
Level Adjustment
screw
FP-XMWAB
Phone number: 877-281-2169