Ge security industrial, General specifications, Ordering/electrical specifications – Edwards Signaling 111 GuardSwitch User Manual
Page 2: Wire color code
©2004 GE Security Industrial. GE Security Industrial reserves the right to change specifications without notice.
I-0400-0304 12517 Rev
D
www.ge-security.com/industrial
12345 SW Leveton Drive
Tualatin, OR 97062
Phone: 800-247-9447
Fax: 503-691-7563
GE Security
Industrial
General Specifications
Enclosure
ABS Plastic
Temperature Range
-40
°
F to 180
°
F (-40
°
C to 80
°
C)
Environmental
Hermetically Sealed Contact Switch
Sealed in Polyurethane
NEMA Rating
1, 2, 3, 4, 4X, 5, 6, 12
Protection Class
IP 67
Response Time
1 msec
Life Cycles
100,000 Under Full Load;
22/2 Jacketed (J)/0.24" (0.62cm)
Up to 200,000,000 Under Dry Circuit
Lead Types/O.D.
18/2 or 18/3 Jacketed (J)/O.24" (0.62cm)
18/3 (K)/0.33" (0.84cm)
UL/CSA
All Models
Ordering/Electrical Specifications
PART NUMBER
CONTACT
1
LOAD RATING
SWITCHING VOLTAGE
SWITCHING CURRENT
CONTACT
SENSE
2
BREAK RANGE
LEAD LENGTH
LEAD
CONFIG.
AC/DC
MAXIMUM, AC/DC
MAXIMUM, AC/DC
RESISTANCE
NOMINAL
NOMINAL
NOMINAL
SIZE
111-3Y-06(J)
N.C.
100VA/84W
3
3.0A
3
@34V 3.0A
3
@28V
1.0 Ohms
0.7"(1.8cm)
1.2"(3.0cm)
6'(1.8m)
18/2
111-3Y-12(J)
N.C.
100VA/84W
3
3.0A
3
@34V 3.0A
3
@28V
1.0 Ohms
0.7"(1.8cm)
1.2"(3.0cm)
12'(3.6m)
18/2
111-4Y-06(K)
SPDT
100VA/84W
3
3.0A
3
@34V 3.0A
3
@28V
1.0 Ohms
0.7"(1.8cm)
1.2"(3.0cm)
6'(1.8cm)
18/3
111-4Y-12(J)(K)
SPDT
100VA/84W
3
3.0A
3
@34V 3.0A
3
@28V
1.0 Ohms
0.7"(1.8cm)
1.2"(3.0cm)
12'(3.6m)
18/3
111-5X-06(J)-G1
4
N.O.
10VA/10W
[email protected] [email protected]
0.5A@20V
0.5A@20V
NA
0.7"(1.8cm)
1.7"(4.3cm)
6'(1.8m)
22/2
111*-6Y-05(J)
N.O.
25VA/25W
0.7A@35V
1.0A@25V
0.2 Ohms
1.0"(2.5cm)
2.0"(5.1cm)
5'(1.5m)
22/2
111-6Y-06(J)(K)
N.O.
25VA/25W
0.7A@35V
1.0A@25V
0.2 Ohms
1.0"(2.5cm)
2.0"(5.1cm)
6'(1.8m)
22/2
111-6Y-12(J)(K)
N.O.
25VA/25W
0.7A@35V
1.0A@25V
0.2 Ohms
1.0"(2.5cm)
2.0"(5.1cm)
12'(3.6m)
22/2
111-7Y-06(J)(K)
N.O.
100VA/84W
3
3.0A
3
@34V 3.0A
3
@28V
1.0 Ohms
0.7"(1.8cm)
1.2"(3.0cm)
6'(1.8m)
18/2
111-17Y-06(J)
N.O.
100VA/100W
3.0A@34V
3.0A@34V
0.5 Ohms
0.7"(1.8cm)
1.2"(3.0cm)
6'(1.8m)
18/2
111-7Y-12(J)(K)
N.O.
100VA/84W
3
3.0A
3
@34V 3.0A
3
@28V
1.0 Ohms
0.7"(1.8cm)
1.2"(3.0cm)
12'(3.6m)
18/2
111-Y
Actuator Only
Included with all switches unless otherwise noted.
Warning— Each electrical rating is an individual maximum and cannot be exceeded!
1
Configuration with actuator away from the switch
2
Proximity of ferrous materials usually reduces sense range — typically by 50%. The shape and type of material cause a wide diversity of effects.
Testing is required to determine actual sense range for specific applications.
3
Rated at 3.0A for 6,000 cycles only. Other ratings are at 100,000 cycles.
4 Special cable exit (not UL)
Parallel Actuation
The interlock switch and actuator magnet should be mounted in only three
configurations for actuation:
Three configurations are appropriate for interlock applications. The parallel
actuation can result in on/off/on signal if the actuator passes by the switch rather
than coming to rest in proximity to it. This is NOT a recommended configuration for
interlock applications.
Perpendicular
Actuation
Door
Actuation
Pivot Actuation
Best
Best
Figure 2
Good
File E 122942
LR89176
2. Mount the switch on the stationary frame of the machine and connect the electrical
wiring. When mounting the switch on an ungrounded machine, connect the ground
lead to one of the mounting screws.
3. Mount the actuator on the movable guard, door, or gate.
Wire Color Code
Black
COM
White
N.O.
Red
N.C.