KEPCO HSF 600W Series (no suffix, suffix C) Operator Manuals User Manual
Kepco, Operator’s manual, Hsf 600 watts
IMPORTANT NOTES:
1)
This manual is valid for the following Model and associated serial numbers:
MODEL
SERIAL NO.
REV. NO.
2)
A Change Page may be included at the end of the manual. All applicable changes and
revision number changes are documented with reference to the equipment serial num-
bers. Before using this Instruction Manual, check your equipment serial number to identify
your model. If in doubt, contact your nearest Kepco Representative, or the Kepco Docu-
mentation Office in New York, (718) 461-7000, requesting the correct revision for your
particular model and serial number.
3)
The contents of this manual are protected by copyright. Reproduction of any part can be
made only with the specific written permission of Kepco, Inc.
Data subject to change without notice.
KEPCO
®
THE POWER SUPPLIER™
MODEL
OPERATOR’S MANUAL
KEPCO INC.
KEPCO, INC. ! 131-38 SANFORD AVENUE ! FLUSHING, NY. 11355 U.S.A. ! TEL (718) 461-7000 ! FAX (718) 767-1102
email: [email protected] ! World Wide Web: http://www.kepcopower.com
An ISO 9001 Company.
HSF 600 Watts
©2013, KEPCO, INC
P/N 228-1588-P
HSF 600 WATTS
POWER SUPPLY
HSF 600 WATTS
POWER SUPPLY
SINGLE OUTPUT POWER SUPPLIES
SINGLE PHASE, POWER FACTOR CORRECTED
UNIVERSAL AC INPUT
HSF 12-53, HSF 15-43, HSF 24-27,
HSF 28-23, HSF 48-13
HSF 12-53C, HSF 15-43C, HSF 24-27C,
HSF 28-23C, HSF 48-13C
SN 488-B, SN 488-D, JQE 1/4 Rack Series, KLP Series User Manual, Rev 2, KLP Series User Manual, Rev 4, KLP Series User Manual, KFD 15-10-28W, KFD 6-25-28W, KFD 6-25-60W, KFD 15-10-60W, KFD 24-4.2-28W, JQE Full Rack Series, BHK-MG VISA Driver Manual (Both Full and 1/2 Rack), ABC VISA INSTRUMENT DRIVER, ATE-DMG SERIES, HSF 300W Series (no suffix) Operator Manuals
Document Outline
- 1.1 Scope of Manual
- 1.2 Description
- 1.3 Options
- FIGURE 1. HSF Rear Panel Connector and RA 19-4C Rack Adapter I/O Connector
- TABLE 1. HSF Rear Connector Pin Assignments
- TABLE 2. Output Ratings and Specifications
- FIGURE 2. Power Rating Vs. Temperature (Input: 95 to 264V a-c)
- TABLE 3. Power Supply Ratings and Specifications
- FIGURE 3. Mechanical Outline Drawing Of The HSF 600W Power Supply
- 3.1 DIP Switch Configuration
- FIGURE 4. DIP Switch Configuration
- 3.2 Front Panel Access.
- 3.3 Keying
- FIGURE 5. Front Panel Controls, Indicators and Test Points
- 3.4 Output Voltage Control
- 3.4.1 Front Panel Voltage Control
- 3.4.2 Remote Voltage Control
- FIGURE 6. DIP Switch Settings for Control of Output Voltage
- TABLE 4. Minimum Conditions for Relay and LED Operation
- FIGURE 7. Connections For Remote Voltage Control
- 3.5 Remote On-Off
- FIGURE 8. DIP Switch Settings for Using RESET button or Remote ON-OFF
- 3.6 Protection Circuits
- 3.6.1 Overvoltage And Overtemperature Protection
- 3.6.2 Overcurrent Setting and Protection
- 3.6.3 Fan Failure
- 3.6.4 Undervoltage
- 3.7 Alarm Settings
- 3.7.1 Visual Alarm.
- 3.7.2 Alarm Signals.
- 3.7.2.1 Internal Isolated Relay Alarm
- 3.7.2.2 Optically-Coupled Logical Alarm
- FIGURE 9. DIP switch settings for Optically Coupled Logical Alarm
- FIGURE 10. Output Alarm Circuit Optically Isolated
- FIGURE 11. ±PF Power Failure Optocoupler Timing Diagram
- 3.8 Local/remote Sensing
- 3.9 Retaining Latches
- 5.1 Adjusting the Voltage
- 5.2 Parallel Connections, Standard and C Models