SHIMPO DT-725 - Manual (Page 3)

When FPM reading is displayed but unit is not flashing,
flash tube may need to be replaced.
1. Unplug line cord from power line. Turn power switch
OFF. Wait a few minutes until stroboscope is cool
before replacing flash tube.
2. Remove protective window by removing the 4 screws.
3. Use a rag and pull the tube out of its socket by rocking
it slightly up and down. Do not use bare hands to
remove tube, it may break and cause injury.
4. Insert new tube using the technique mentioned above.
Make sure that the tube is placed properly in the socket
otherwise it will touch the reflector. Tube should be set
symetrically within the neck of the reflector.
5. Replace protective window.
Flash Tube Replacement
MODEL MODEL MODEL MODEL MODEL DT DT DT DT DT- 725(DC) - 725(DC) - 725(DC) - 725(DC) - 725(DC)
FLASHING RANGE FLASHING RANGE FLASHING RANGE FLASHING RANGE FLASHING RANGE 40 — 12,500 FPM (Flashes Per Minute)
ACCURACY ACCURACY ACCURACY ACCURACY ACCURACY ±0.02% of reading
RESOL RESOL RESOL RESOL RESOLUTION UTION UTION UTION UTION 0.1 , 40.0 – 4,999.9 FPM
0.2 , 5,000.0 – 7,999.8 FPM
0.5 , 8,000.0 – 9,999.5 FPM
1
.0 , 10,000 .0 – 12,500 .0 FPM
DISPL DISPL DISPL DISPL DISPLAAAAAYYYYY 5-Digit LED, 0.3" (8 mm) height
R RR RRAAAAATE TE TE TE TE Divide by 2, Multiply by 2
UPDA UPDA UPDA UPDA UPDATE TIME TE TIME TE TIME TE TIME TE TIME Ext. mode: varies with flashing rate
OPER OPER OPER OPER OPERAAAAATING TIME TING TIME TING TIME TING TIME TING TIME 1 hour when fully charged
FLASH TUBE POWER/LIFE FLASH TUBE POWER/LIFE FLASH TUBE POWER/LIFE FLASH TUBE POWER/LIFE FLASH TUBE POWER/LIFE Xenon, 10 W, 100 million flashes
FL FL FL FL FLASH DUR ASH DUR ASH DUR ASH DUR ASH DUR AAAAATION TION TION TION TION 10 - 15 µ s
SIGNAL OUTPUT SIGNAL OUTPUT SIGNAL OUTPUT SIGNAL OUTPUT SIGNAL OUTPUT NPN Open Collector (24 VDC max.,
50 mA) 150
µ s typical
PHASE SHIF PHASE SHIF PHASE SHIF PHASE SHIF PHASE SHIFTTTTT Internal mode only by using the “+”
and “–” switches
EXT EXT EXT EXT EXT. TRIGGER . TRIGGER . TRIGGER . TRIGGER . TRIGGER a) 12-24 VDC thru a 3-wire NPN output
sensor (requires external power supply)
INPUT SIGNAL INPUT SIGNAL INPUT SIGNAL INPUT SIGNAL INPUT SIGNAL b) 12 VDC thru a 2-wire proximity
sensor (leakage current 1 mA max.,
Load current 8 mA min.)
c) Switch or Relay contact
LLLLLOW BA OW BA OW BA OW BA OW BATTTTTTERY INDICA TERY INDICA TERY INDICA TERY INDICA TERY INDICATOR TOR TOR TOR TOR Yes
OPER OPER OPER OPER OPERAAAAATING TEMPER TING TEMPER TING TEMPER TING TEMPER TING TEMPERAAAAATURE TURE TURE TURE TURE 32° – 104° F (0 – 40° C)
DIMENSIONS DIMENSIONS DIMENSIONS DIMENSIONS DIMENSIONS 9" L x 4.3" W x 8.5" H
(Height includes handle)
WEIGHT WEIGHT WEIGHT WEIGHT WEIGHT 2.75 lbs (1.25 Kgs)
ACCESSORIES AVAILABLE ACCESSORIES AVAILABLE ACCESSORIES AVAILABLE ACCESSORIES AVAILABLE ACCESSORIES AVAILABLE Carrying Case
Specifications