Atlas Sound XLTE - Manual (Page 17)

PAGE 15 Community XLT / XLTE Series Owner’s Manual
4.8.6 41 Positioning and Horn Rotation
The 41 can be positioned in several ways. When used as a floor monitor either of the two backs may be placed on
the floor to vary the aiming angle. One provides an up-angle of 30 degrees from the floor and the other an up-angle
of 45 degrees from the floor. The 41 may also be used upright as a PA loudspeaker.
The 41 is shipped from the factory oriented for floor monitor use so that, in a horizontal position, its HF coverage is
90 degrees horizontal by 40 degrees vertical. For operating it in an upright position as a PA loudspeaker, normally
the horn should be rotated so its horizontal coverage pattern will be 90 degrees. (See SECTION 7.3)
4.8.7 Front Grille
The front grille is powder coated, 16 gauge perforated steel, held in place with screws. This provides a secure
fastening while allowing easy removal for service.
4.8.8 Enclosure Finish
XLT: The XLT enclosures are finished with a dense, black carpet material held in place with an industrial strength
adhesive backing.
XLTE: The XLTE enclosures are finished with a black, high durability urethane coating.
4.9 OPTIONAL ACCESSORIES
Various accessories are available from Community and third party sources for mounting, supporting, or protecting
the loudspeakers.
4.9.1 Community Accessories
SB5 – Five foot long, 1-/3/8 in. / 35 mm O.D., black-painted steel pole for pole mounting a full-range loudspeaker on
another loudspeaker such as an XLT42E on an XLT51E, or an XLT41 on an XLT51.
CSSUPKIT – Suspension kit with two steel straps that attach to the threaded inserts (T-nuts) on XLT and XLT48E
models. The straps have a series of 3/8 in. / 9.5 mm diameter holes for attachment to rigging.
WB1 – Two steel brackets that can be attached to the T-nuts on XLT and XLT48E models. Used for mounting to walls
or ceilings. Not usable with the XLT41E.
EYBLTKIT – Four forged steel eyebolts and four steel, locking, cup-washers for the mounting-rigging points on XLTE
models (except XLT41E and XLT48E).
4.9.2 3rd Party Accessories
The following are some US companies that make accessories that may be used with Community Products. Outside
the US, contact your Community Distributor for similar companies in your specific country or region.
Suspension Hardware / Systems Mounting Brackets
ATM Fly-Ware™ Omnimount™ Systems
21000 South Wilmington Avenue 1501 West 17th Street
Carson, CA 90810-1247 Tempe, AZ 85281
Tel: (310) 834-5914 Fax: (310) 834- 3042 Tel: (602) 829-8000 Fax: (602) 796-5000
Road Cases Stands and Stand Sockets
Art*Tec, Inc. Ultimate Support™ Systems, Inc.
330 Pusey Avenue 2506 Zurich Drive
Collingdale, PA 19023 Ft. Collins, CO 80524
Tel: (800) 952-4107 Fax: (610) 461-5720 Tel: (303) 493-4488 Fax: (303) 221-2274
Star Case manufacturing Co., Inc. Atlas/Soundolier
648 Superior Avenue 1859 Intertech Drive
Munster, IN 46321 Fenton, MO 63026
Tel: (219) 922-4446 Fax: (219) 922-4442 Tel: (314) 349-3110 Fax: (314) 349-1251