Applica LitterMaid Elite LME9000 - Manual (Page 6)

10 9
After 9 hours the unit will perform one litter raking cycle and then resume normal
operation. The 9-hour sleep mode and the 15-hour normal operation repeat at set
time every 24 hours.
To Program the Sleep Mode Timer (T):
1. Set the clock to the time of day by pressing the hour then
minute button.
Note: If setting P.M., be sure light in the upper left corner of
the display is lit. The LED continues to blink 12:00 until the
clock is set.
2. Press the SET button on the control panel to begin programming.
3. Sleep mode red LED starts blinking.
4. Press the HOUR and MINUTE button (light indicating P.M. is in the upper left
corner of the LED display) to set the time you want the sleep mode to begin
(for example, if you set the time for 10:00P.M. the unit remains in the sleep
mode until 7:00A.M. (9 hours)).
5. Sleep mode time is automatically accepted if no buttons are pressed for
3 seconds or more.
6. Sleep mode red LED stops blinking and red LED is not lit.
7. Sleep mode is now set, but not activated.
To Activate Sleep Mode:
1. Press and hold the set button.
2. Steady red light comes on to indicate that the sleep mode is activated.
To Deactivate Sleep Mode:
1. Sleep mode must be activated (red LED lit) to be deactivated.
2. Press the SET button, steady red LED is no longer lit.
Ionic Air Cleaner:
• As soon as the cat leaves the litter box, the sensor activates the 10-minute
countdown and the ionic air cleaner.
• The ionic air cleaner stays on during the countdown and the cleaning cycle.
• If the sleep timer is activated the rake will not cycle for 9 hours from the set
sleep mode time (the ionic air cleaner will automatically turn on every hour
for 10 minutes).
Optional Items:
For more information: call, 1-800-738-0245; or visit our website,
www.littermaid.com.
Litter Box Carpet:
• Place the assembled unit on the carpet.
LitterMaid Kitty Kabana™ litter box cover:
Assemble to cover unit (U). (See instruction sheet.) •
U
• Assists in cleaning the rake (N).
• Aids in the removal of small waste particles (P).
11. Install paw cleaning ramp: (Certain models)
• The paw-cleaning ramp has two pivot pins that fit into holes
on the sides of the waste receptacle compartment cover.
• Position the paw-cleaning ramp with carpet-side facing up.
• Insert the pivot pins into the holes (Q).
• Tug slightly on the ramp to ensure that it is firmly in place.
12. Install rake:
Align tracks on back of rake (each end) and slide into
grooves on motor housing (R).
13.Remove the AC adapter from where it is packed in the
styrofoam and plug it into the unit (S).
• Plug the cord into a standard electrical wall outlet.
• Turn the ON/OFF switch to ON. The rake will automatically
run through its first cleaning cycle and smooth out the litter.
Important: When the ON/OFF button is in the OFF position it
only disables the rake function.
14. If the LitterMaid® Kitty Kabana™ litter box cover is not being used, place
the 4 tent plugs into the 4 holes on top housing.
Note: Always use both hands to move LitterMaid® litter box by holding handle
cutouts located on each side of the tray.
Setting the Clock:
1. Set the clock to the time of day by pressing the HOUR then MINUTE button.
Note: If setting P.M., be sure light in the upper left corner of the display is lit.
The LED continues to blink 12:00 until the clock is set.
Programming the Sleep Timer:
Sleep mode deactivates the cleaning cycle for a period of 9 hours. During this
time the ionic air cleaner automatically turns on for 10 minutes every hour to
freshen the air.
•
S
T
R
Q
N
P