HP Visualize J210 Workstation User Manual
Read before installing
Hewlett-Packard Company
3404 East Harmony Road
Fort Collins, Colorado 80528
Pub. No. A7853-90011
Read Before Installing
CD-RW Drive for HP-UX Workstations
For a tutorial on creating CD-RW masters on HP-UX systems, refer to the
/opt/OpenSource/cdrtools-1.10/USER_GUIDE.pdf
file on the CD-RW software media.
Supported Features.
This product (and associated software) is intended to be used primarily
as a data storage and exchange device. Hewlett-Packard does not support the creation or duplication
of audio CDs using this product and software.
Hardware Installation
The CD-RW drive you have purchased may be installed in any one of several models of HP-UX Work-
stations. For complete instructions on how to install the drive on your system, please refer to the
appropriate Owners Guide, Parts Replacement Guide or Technical Reference for your system. These
documents can be found at:
http://www.hp.com/workstations/support/documentation/
hpux_manuals.html
This CD-RW drive can either be installed to replace an existing CD-ROM drive or as a new drive
where none existed before. It also may have been integrated into your computer at the HP factory.
If you are replacing an existing CD-ROM drive with the CD-RW drive, at minimum you must load the
PHKL_24282 (for HP-UX 11.0) or PHKL_24283 (for HP-UX 11i) patches from the CD-RW software
media. Subsequent patches are recommended in lieu of these minimum required patches. If you are
installing a new drive where none existed before, you must load the patches from the
http://us-support.external.hp.com
web site. Make sure these patches are installed on your system
before attempting to install the hardware.
Feature
HP Support
Audio CD duplication
No (both GUI and command line)
Create bootable HP-UX CD
GUI=No, Command line=Yes
Duplicate bootable CD
Yes (GUI and command line) if CD is valid
Multi-Session recording
No (both GUI and command line)
Copying HP-UX install CD
For more information go to USER_GUIDE.pdf on
the CD
Copy CD-to-CD
No (both GUI and command line)
Disk-at-once recording
No (both GUI and command line)
Track-at-once recording
Yes (both GUI and command line)
Data recording (any file type)
Yes (both GUI and command line)
Visualize c200 Workstation, Visualize c100 Workstation, c3700 Workstation, Visualize J5600 Workstation, Visualize b132L Plus Workstation, Workstation c3650, Visualize b160L Workstation, Visualize J7000 Workstation, Visualize J280 Workstation, Visualize c160 Workstation, Visualize c180 Workstation, Visualize c360 Workstation, Visualize b2000 Workstation, Visualize b180L Workstation, b2600 Workstation, Visualize J210XC Workstation, Visualize c240se Workstation, Visualize J282 Workstation, Visualize c160L Workstation, Visualize J2240 Workstation, Visualize b132L Workstation, Visualize J5000 Workstation, Visualize c3000 Workstation, Visualize J200 Workstation, Visualize c110 Workstation, Visualize c180xp Workstation, j6700 Workstation, Visualize c3600 Workstation, Visualize c200c240 SSP Workstation, Visualize c240 Workstation, Visualize b1000 Workstation
Document Outline
- Read Before Installing
- CD-RW Drive for HP-UX Workstations
- For a tutorial on creating CD-RW masters on HP-UX systems, refer to the /opt/OpenSource/cdrtools-...
- Supported Features.
- Hardware Installation
- Software Installation
- Note: About Open Source software
- 1. Make sure the PHKL_24282 (for HP-UX 11.0) or PHKL_24283 (for HP-UX 11i) patch is installed on ...
- 2. Install the software on your system. As root, execute the following command: / usr/sbin/swinst...
- 3. Make sure your system is backed up and shutdown properly.
- 4. Install the CD-RW hardware. See the “Hardware Installation” section of this document.
- 5. Boot your system and run the MKNOD.hpux script that is provided with the X-CD-Roast software: ...
- Quick Guide - How to Write a CD on an HP-UX System
- Caution: CD writing is a real-time process which must run constantly at the selected recording sp...
- First Time Users of X-CD-Roast
- 1. Start X-CD-Roast by executing:
- 2. Click the Setup button, the Setup screen will appear with six tabs.
- 3. Click the third tab: HD Settings. You must name the scratch directory to be used when building...
- 4. Click the fifth tab: Options. At the bottom of this screen, from the pull-down list labeled De...
- 5. Click the sixth tab User. This will provide access and permissions to the users and hosts. Cha...
- 6. On the far left, click on Save Configuration. A new window will appear, then lick the OK button.
- 7. On the far left, click on the OK button.
- Repeat Users of X-CD-Roast
- 1. Start X-CD-Roast:
- 2. Click the Create CD button
- 3. Click the Master Tracks button. On the CreateCD screen, there will be five tabs and you will o...
- 4. The left tab: Master Source has 2 panes. Under the right hand pane, click on the Display Direc...
- 5. In the right pane labeled File/Directory View, select the files/directories you want to place ...
- 6. To the tab: Create Session/Image. Click on the Calculate Size button. A new window will appear...
- 7. At the bottom right of the screen, click on the Master and write on-the-fly button. A new wind...
- 8. When the CD burning has finished, the CD drawer will open automatically. Click on the OK butto...
- 9. Click the Back to main menu button.
- 10. Click the Exit button. A new window will appear, then click the Yes button.
- 11. Close the CD tray. On the HP-UX workstation containing the CD-writer, execute (as root):
- 12. You should now be able to see all of your files within the /cdrom directory.
- 13. OPTIONAL: You may copy the file system to the desired location. File permissions, owners and ...
- Software Licensing Agreement for Required HP-UX Patches