HP Pavilion fx50 15 inch Flat Panel Monitor User Manual
HP Monitors
Advertising
Table of contents
Document Outline
- Notice
- The information contained in the documents accompanying this product is subject to change without...
- Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not li...
- Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequentia...
- Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment...
- These documents contain proprietary information that is protected by copyright. All rights are re...
- Hewlett-Packard Company Home Products Division P.O. Box 4010 Cupertino, CA 95015-4010 USA
- © Copyright Hewlett-Packard Company, 2001. All rights reserved.
- Hewlett-Packard is a registered trademark of Hewlett-Packard Company in the United States of Amer...
- hp pavilion fx50 P3901 15-inch lcd monitor (15-inch Viewable Image) User’s Guide
- Important Safety Instructions
- What Your New Monitor Offers
- Unpacking Your Monitor
- Setting Up Your Monitor
- Where to Place the Monitor
- WARNING Before you connect any cables, or install your HP monitor, refer to the safety instructio...
- Connecting the Cables
- 1 Make sure the system power is turned off.
- 2 Plug the signal cable into the signal connector at the rear of thePC.
- 3 Plug the adapter output cable into the jack at the rear of the monitor and the power cord to th...
- 4 Plug the video cable into the video connector at the rear of the monitor. Secure the cable by t...
- 5 Connect the audio cables to the connectors according to the following color definitions: Red + ...
- 6 Connect the power cord to the power source.
- 7 Turn on the computer and the monitor.
- Connecting the Speakers
- Changing the Monitor Viewing Position
- Connecting the Cables
- How To Install The Drivers
- Windows 95 and 98 Users
- 1 Click on Start, select Settings, then click Control Panel.
- 2 Double click on Display.
- 3 Click on the Settings tab.
- 4 Click on Advanced Properties or Advanced... and select the Monitor tab.
- 5 Click on Change... to select the model of the HP Monitor you are using.
- 6 Click on Have Disk...
- 7 Click on Browse... to find the P3901.INF file on your CD-ROM under the \Drivers directory and c...
- 8 Select your monitor type from the Models box and click on OK to install the selected monitor.
- Windows 2000 Users only
- 1 Click on Start, select Settings, then click Control Panel.
- 2 Double click on Display.
- 3 Click on the Settings tab.
- 4 Click on Advanced Properties or Advanced... and select the Monitor tab.
- 5 Click on Properties.
- 6 Click on the Driver tab.
- 7 Click on Update Driver... and click on Next.
- 8 Select the Recommended option and click on Next.
- 9 Check the Specify a Location box.
- 10 Find and open the P3901.INF file on your CD-ROM under the \Drivers directory and click on OK.
- 11 Click on Next to install the selected monitor.
- Windows 95 and 98 Users
- Adjusting Your Monitor
- A Look at the Control Panel
- ¿
- ¿
- ¡
- ¬ Ã
- ƒ
- NOTE It is recommended that you select a video mode of 1024 x 768 at 60Hz on your computer for op...
- Automatic Setup
- Manual Setup
- 1 Display the pattern using the CD-ROM as described above.
- 2 Press Enter to display the OSD menu.
- 3 Select the Geometryicon.
- 4 Select Pixel Clockand adjust the value to minimize vertical bars.
- 5 Select Phaseand adjust the value to minimize horizontal bars.
- 6 Select Horizontal Positionand Vertical Positionto adjust screen position.
- 7 Press the Exit button to save the values.
- Using Your Monitor
- Setting the Language
- The Auto Button
- To
- NOTE For best results, it is recommended to use the CD-ROM supplied with the monitor to display a...
- The On-Screen Display (OSD) Main Menu
- ¿
- Making Adjustments
- 1 Press the Menu button to access the main OSD.
- 2 Use the or buttons to move through the sub-menus, and press to enter the sub-menu.
- 3 Use the or buttons to move through the various choices within the sub-menu, and validate your c...
- 4 Press the or buttons to adjust the settings, then press the Menu button to exit the sub-menu.
- 5 Press the Menu button to exit the respective sub-menus, and press the Menu button to exit the OSD.
- Making Adjustments
- NOTE Before exiting the OSD, you are prompted to save your settings.
- The Sub-Menus
- Luminance
- 1 Press the Menu button and use the or buttons to highlight the Luminance icon.
- 2 Press the button to select the feature.
- 3 Use the or buttons to choose either Contrast or Brightness, then press to select it.
- 4 Press or buttons to adjust the settings (the settings are automatically saved).
- 5 Press the Menu button to exit the sub-menu, then press the Menu button to exit the respective s...
- 6 Press the Menu button to exit the OSD.
- Geometry
- 1 Press the Menu button and use the or buttons to highlight the Geometry icon.
- 2 Press the button to select the feature.
- 3 Use the or buttons to choose one of the menu items listed above, then press the button to selec...
- 4 Press or buttons to adjust the settings (the settings are automatically saved).
- 5 Press the Menu button to exit the sub-menu, then press the Menu button to exit the respective s...
- 6 Press the Menu button to exit the OSD.
- Auto Adjustment
- Luminance
- The Sub-Menus
- NOTE For optimum results, it is recommended that you display the pattern provided on the CD-ROM s...
- Color Adjustment
- C1
- C2
- C3
- 9300k
- 6500k
- 5800k
- 1 Press the Menu button and use the or buttons to highlight the Color icon.
- 2 Use the or to choose one of the options listed above.
- 3 To validate your choice, use the Menu button to exit the sub- menus until you are prompted to s...
- 4 To make changes in User Mode, use the or buttons to highlight the User Mode icon then press the...
- 5 Use the or buttons to choose R, G or B (Red, Green or Blue), then press the button to enter the...
- 6 Use the or buttons to make the required adjustments (the settings are automatically saved).
- Audio
- 1 Press the Menu button and then use the or buttons to locate the Volume sub-menu, then press the...
- 2 Press the button to choose the required menu item.
- 3 Use the or buttons to adjust the setting (the settings are automatically saved).
- 4 Press the Menu button to exit the sub-menu, then press the Menu button to exit the respective s...
- 5 Press the Menu button to exit the OSD.
- Miscellaneous
- • Screen Geometry
- • Horizontal Frequency
- • Vertical Frequency
- • Brightness / Contrast
- WARNING By pressing the button all previous adjustments are lost (refer to “Adjusting Your Monito...
- Troubleshooting
- Technical Specifications
- Care and Cleaning
- Environmental Information
- Regulatory Information