GE ZISS480NXSS - Manual (Page 6)

monogram.com
89
B
u
ilt
-i
n
a
ll
-r
e
fr
ig
e
ra
to
rs
an
d
al
l-
fre
e
ze
rs
Fu
lly i
n
te
g
ra
te
d
re
fr
ig
era
to
rs
/
w
ine
r
ese
rv
e
B
uil
t-
in
b
ot
to
m
-f
re
e
ze
r
re
fr
ig
e
ra
to
rs
Fre
e
-s
tan
d
in
g
re
fr
ig
era
to
rs
B
u
il
t-
in
si
d
e
-b
y-
si
d
e
re
fr
ig
e
ra
to
rs
Advance planning for built-in custom side-by-side refrigerators
If you choose to install framed
panels, they must be cut to the
dimensions shown. The panels
will slide into the frame on the
door and grille.
If the custom panel is less than
1/4" thick, and it fits loosely in
the door frame, it can be backed
up with a piece of filler material
or foam tape to improve the fit.
Important note: Maximum
weight for fresh-food panel is 75
pounds, 53 pounds for freezer
panel and 18 pounds for the
grille panel.
1/4" framed panel dimensions
Side-by-side (in inches)
A B C D E
36" models 33-7/8 9 68-3/8 14-9/16 18-9/16
42" models 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16
48" models 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16
Dispenser cutout position (in inches)
F G
36" models 17-13/16 3-1/8
42" models 17-13/16 3-1/8
48" models 17-13/16 5-1/8
194Dia64
Fresh Food
Panel
Freezer
Panel
E D
F
G
A
B Grille Panel
C
Dispenser
Cutout
9-5/8"
194Dia63
Dispenser Cutout
15-3/8"
194Dia59
1/4"
Panel
Door
5/16"
Trim
Reveal
Dispenser models
These refrigerators are supplied with two dispenser trims, one for
framed panels and one for overlay panels.
1/4" framed panel
The framed panel must be 1/4" nominal thickness to fit the
dispenser trim.
• The dispenser trim fits over the custom panel and snaps into
the freezer door.
• If the panel is less than 0.250" thick, a noticeable gap may be
created around the dispenser trim. Foam tape may be applied
on the door to improve the fit.
• If the panel is more than 0.250" thick, the dispenser trim
cannot be secured to the door.
696Dia3
1/4"
Framed
Panel
1/4" Dispenser Trim
FREEZER DOOR
0.250"
Thick
Ice / Water Dispenser
1/4" Backer Panel
.10" Spacer
Panel
3/4" Overlay Dispenser Trim
3/4" Overlay
Panel
FREEZER DOOR 1.100"
Total
Thickness
Ice / Water Dispenser
696Dia4
3/4" overlay panels
The overlay dispenser trim is designed to fit a total panel
thickness of 1.100".
• If the panel is less than 1.100" thick, a noticeable gap may
be created around the dispenser trim.
• If the panel is more than 1.100" thick, the dispenser trim
cannot be secured to the door.
• The overlay panel must be constructed according to the
specifications shown to achieve the correct total thickness.
• Alternative panel construction methods such as
securing a 3/4" panel to a 1/4" backer panel cannot be used.
Another method, routing a 3/4"-thick panel on all sides,
cannot be used. These methods will not result in the required
1.100" panel thickness.
• When a raised panel design is to be used, a custom middle
rail is required. See page 75 for details.