Alpine CDA-9847 - Manual (Page 19)

18
-EN
POWER IC ON : The speakers are driven by the built-in amplifier.
• No sound is produced by the system when the power output is set to
OFF.
Setting the External Digital Input
D-AUX ON / D-AUX OFF (Initial setting)
When an ALPINE Ai-NET compatible digital audio processor and an
Ai-NET non-compatible DVD player (DVE-5207) are connected, set
D-AUX to ON to enjoy 5.1-channel surround sound.
• After setting D-AUX to ON, make the setting in “Connecting an
Optical Digital Compatible Audio Processor and an Ai-NET Non-
Compatible DVD Player.”
• Press SOURCE/POWER, and select the D-AUX mode, and adjust
the volume, etc.
• Depending on the connected audio processor, DVD player sound
may continue to be output, even though the source is changed to
another one. If this occurs, set the DVD player's power to OFF.
Connecting an Optical Digital Compatible Audio
Processor and an Ai-NET Non-Compatible DVD Player
H510 /OTHER (Initial setting)
After setting D-AUX to ON in “Setting the External Digital Input,” do
the following according to the audio processor type:
H510:
If the PXA-H510 and the Ai-NET non-compatible DVD player
(DVE-5207) are connected (using optical cable), use the H510
setting. Connect the DVD player (using optical cable) to the
optical digital input terminal (for DVD Player).
OTHER:
If an audio processor other than PXA-H510 and the Ai-NET
non-compatible DVD player (DVE-5207) are connected (using
optical cable), use the OTHER setting. Connect the DVD
player (using optical cable) to the optical digital input terminal
(for Head unit).
• After input selection is completed, turn the ignition off and back on
again. Setting of the optical digital input switch is completed.
Speakers
Front
left
Front
right
Rear
left
Rear
right
SPEAKER
RIGHT FRONT
SPEAKER
RIGHT REAR
SPEAKER
LEFT REAR
SPEAKER
LEFT FRONT
SAT Radio Receiver (Optional)
SAT Receiver: XM or SIRIUS Receiver
When an optional XM or SIRIUS Receiver Box is
connected via the Ai-NET bus, the following
operations may be performed. However, the XM
Receiver and SIRIUS Receiver cannot be connected at
the same time.
Receiving Channels with the SAT Radio
Receiver (Optional)
About SAT Radio
Satellite Radio* is the next generation of audio entertainment, with
over to 100 digital channels. For a small monthly fee, subscribers can
hear crystal-clear music, sports, news and talk, coast-to-coast via
satellite. For more information, visit XM’s website at
www.xmradio.com., and SIRIUS' website at www.sirius.com.
To receive XM radio, the XM company sold XMDirect™ and
ALPINE Interface Adapter Box (for sale in the near future) will be
required. For details, consult you nearest ALPINE dealer.
* XM and its corresponding logos are trademarks of XM Satellite
Radio Inc.
* SIRIUS and its corresponding logos are trademarks of SIRIUS
Satellite Radio Inc.
• The SAT Receiver controls on the CDA-9847 are operative only
when an SAT Receiver is connected.
1
Press SOURCE/POWER to select XM or SIRIUS
mode.
2
Press BAND to select the desired band.
Each press changes the band:
XM mode:
XM1
→ XM2 → XM3 → XM1
SIRIUS mode:
SR1
→ SR2 → SR3 → SR1
3
Press
8 or 9 to select desired category.
4
Press g or f to select the desired channel.
Holding down g or f will change channels
continuously.
SOURCE/
POWER
Preset buttons
(1 through 6)
BAND
f g F/SETUP TITLE
SEARCH/
Q.S.
Rotary
encoder
8
9