Tuff Country 55905 - Toyota Tundra 99-03 knuckle 5 lift kit - Manual (Page 3)

Hardware Bag 55905NB Includes:
Description
Quantity
5/16”
x 1” bolt 3
5/16” x 1 1/2” bolt 2
5/16” flat washer 10
5/16” lock washer 5
5/16” unitorque nut 5
3/8” x 1 1/2” bolt 4
3/8” flat washer 14
3/8” unitorque nut 10
3/8” lock washer 10
3/8” fender washer 4
1/2” x 1 1/2” bolt 2
1/2” flat washer 4
1/2” unitorque nut 2
1/2” lock washer 2
9/16” x 2 1/2” bolt 2
9/16” flat washer 6
9/16” lock washer 2
3/4” x 4 1/2” bolt 2
3/4” x 5” bolt 2
3/4” flat washer 8
3/4” unitorque nut 4
12 mm unitorque nut 1
12 mm lock washer 1
Hardware Bag 55905SL Includes:
Description
Quantity
S10075 (.750" X .562" X 1.275")
1
S10076 (.750" X .625" X 2.565") 1
S10077 (2" OD X .625" ID washers) 2
S10082 (.875" X .562" X 2.080") 2
MO2382 (Poly bushing) 2
MO3354 (Poly bushing) 2
PB2408 (Poly bushing) 4
PB8297 (Stem mount shock bushing) 4
COTTER-02
2
WIRE TIE 2
LUBE (poly lube packs) 2
Hardware Bag 916NW Includes:
Description
Quantity
9/16” u-bolt high nuts
8
9/16” u-bolt harden washers 8
Special Note: Before installation begins, it is the
customers/installers responsibility to make sure that
all parts are on hand. If any parts are missing, please
feel free to call one of our customer service
representatives @ (801) 280-2777.
Please Follow Instruction Carefully
Before installation begins, measure from the center
of the hub, to the bottom of the fender well, and
record measurements below.
Pre Installation Measurements:
Driver Side Front:______________________________
Passenger Side Front:__________________________
Driver Side Rear:______________________________
Passenger Side Rear:__________________________
At the end of the installation take the same
measurements and compare to the pre-installation
measurements.
Post Installation Measurements:
Driver Side Front:______________________________
Passenger Side Front:__________________________
Driver Side Rear:______________________________
Passenger Side Rear:__________________________
Please follow instructions carefully:
Front End Installation:
1. To begin installation, block the rear tires of the vehicle
so that the vehicle is stable and can’t roll backwards.
Safely lift the front of the vehicle and support the frame
with a pair of jack stands. Place a jack stand on both the
driver and the passenger side. Next, remove the front
wheels and tires from both sides.
2. Working on the front of the vehicle, remove the stock
upper and lower skid plates from the stock location. Save
the stock upper skid plate and the stock hardware for
later re-installation. The stock lower skid plate and stock
lower skid plate hardware may be discarded.
3. Working on the driver side, remove the stock
hardware from the stock sway bar end link and save the
stock hardware for later re-installation. Repeat procedure
on passenger side.
4. Working on the driver side, remove the stock sway bar
from the stock frame location and save the stock
hardware for later re-installation. Repeat procedure on
passenger side. Set the stock sway bar a side for later
re-installation.
5. Working on the driver side, remove the stock ABS line
from the stock spindle. Save the stock hardware for later
re-installation. Also, remove the stock ABS line from any
other attaching points on the stock spindle and the stock
upper control arm. Tie the stock ABS line up and out of
the way in the fender well. Repeat procedure on the
passenger side.