Tuff Country 54900 - Toyota Tacoma 95-04 5 lift kit User Manual
Page 3
Hardware Bag 54900NB Includes:
Description
Quantity
5/16” x 1 1/2” bolts
9
5/16”
flat
washers
18
5/16”
lock
washers
9
5/16” unitorque nuts
9
3/8”
flat
washers
6
3/8”
lock
washers
6
3/8” unitorque nuts
6
1/2” x 1 1/2” bolts
2
1/2”
flat
washers
4
1/2”
lock
washers
2
1/2” unitorque nuts
2
9/16” x 2 1/2” bolts
2
9/16”
flat
washers
1
9/16”
lock
washer
2
3/4” x 4 1/2” bolts
2
3/4” x 5” bolts
2
3/4”
flat
washers
8
3/4”
lock
washers
4
3/4” unitorque nuts
4
8 mm x 35 mm bolts
2
8 mm flat washers
2
8 mm lock washers
2
Hardware Bag 54900SL Includes:
Description
Quantity
S10021 (.500" X .380" X .620")
2
S10075 (.750" X .562" X 1.275")
1
S10076 (.750" X .625" X 2.565")
1
S10077 (2" OD X .625" ID washers)
2
S10082 (.875" X .562" X 2.080")
2
MO2382 (Poly bushing)
2
MO3354 (Poly bushing)
2
PB2408 (Poly bushing)
4
SB34 (Shock bushing)
4
E-CLIP (Rear brake line clip)
1
COTTER-02
2
WIRE TIE
2
LUBE (poly lube packs)
2
Hardware Bag 916NW Includes:
Description
Quantity
9/16” U-bolt high nuts
8
9/16” U-bolt harden washers
8
Special Note: Before installation begins, it is the
customers/installers responsibility to make sure that
all parts are on hand. If any parts are missing, please
feel free to call one of our customer service
representatives @ (801) 280-2777.
Please Follow Instruction Carefully
Before installation begins, measure from the center
of the hub, to the bottom of the fender well, and
record measurements below.
Pre Installation Measurements:
Driver Side Front:______________________________
Passenger Side Front:__________________________
Driver Side Rear:______________________________
Passenger Side Rear:__________________________
At the end of the installation take the same
measurements and compare to the pre-installation
measurements.
Post Installation Measurements:
Driver Side Front:______________________________
Passenger Side Front:__________________________
Driver Side Rear:______________________________
Passenger Side Rear:__________________________
Please follow instructions carefully:
Front End Installation:
1. To begin installation, block the rear tires of the vehicle
so that the vehicle is stable and can’t roll backwards.
Safely lift the front of the vehicle and support the frame
with a pair of jack stands. Place a jack stand on both the
driver and the passenger side. Next, remove the front
wheels and tires from both sides.
2. Working on the front of the vehicle, remove the stock
upper and lower skid plates from the stock location. The
stock hardware and the stock skid plates may be
discarded.
3. Working on the driver side, remove the stock
hardware from the stock sway bar end link and save the
stock hardware for later re-installation. Repeat procedure
on passenger side.
4. Working on the driver side, remove the stock sway bar
from the stock frame location and save the stock
hardware for later re-installation. Repeat procedure on
passenger side. Set the stock sway bar a side for later
re-installation.
5. Working on the driver side, remove the stock ABS line
from the stock spindle. Save the stock hardware for later
re-installation. Also, remove the stock ABS line from any
other attaching points on the stock spindle and the stock
upper control arm. Tie the stock ABS line up and out of
the way in the fender well. Repeat procedure on the
passenger side.
6. Working on the driver side, remove the stock brake