Outback Power Systems MATE3 USB Card Owner’s Manual - Manual (Page 20)

Commands
18 900-0137-01-00 Rev A
Table 21 Command/Response Definitions
Command Response
<SELL:0> Set inverter Selling disabled
<SELL:1> Set inverter Selling enabled
<SELL:?> Returns current inverter sell mode [SELL:s]
s = state,
0=disabled,
1=enabled
<SELLV:nnn> Sets inverter selling battery voltage where nn.n is the selling voltage
<SELLV:+> Increments inverter selling battery voltage
<SELLV:-> Decrements inverter selling battery voltage
<SELLV:?> Returns the selling voltage [SELLV:nnn] when nn.n is the battery selling voltage
<CHG:0> Set the inverter’s charger(s) off
<CHG:1> Set the inverter’s charger(s) auto
<CHG:2> Set the inverter’s charger(s) on
<CHG:?> Returns current charger mode [CHG:m] for inverter
m = mode,
0=Off,
1=On,
2=Auto
<CHGLM:nn> Sets inverter’s AC charger limit amps, where nn = AC charger amp limit
<CHGLM:+> Increments inverter’s charger limits amps
<CHGLM:-> Decrements inverter’s charger limits amps
<CHGLM:?> Returns inverter’s AC charger limit amps [CHGLM:nn]
<AC1INLM:nn> Sets inverter’s AC1 input limit amps
<AC1INLM:+> Increments inverter’s AC1 input limit amps
<AC1INLM:-> Decrements inverter’s AC1 input limit amps
<AC1INLM:?> Returns inverter’s AC1 input limit amps [AC1INLM:nn]
<AC2INLM:nn> Sets inverter’s AC2 input limit amps
<AC2INLM:+> Increments inverter’s AC2 input limit amps
<AC2INLM:-> Decrements inverter’s AC2 input limit amps
<AC2INLM:?> Returns inverter’s AC2 input limit amps [AC2INLM:nn]
<BULK:1> Starts system wide bulk charge (all ports)
<BULK:2> Stops system wide bulk charge, ie goto float (all ports)
<BULK:?> Returns the current bulk charge state [BLK:s] (all ports)
s = state,
s=2 bulk charge stopped,
s=1 bulk charge enabled
<TEMP:p> Returns inverter’s internal temperatures, p = port 0-10, [TEMP:p,F,C,X]
where p = port 1-10, F=FET, C=CAP, X=Transformer temps in degrees C
If inverter is a Radian series, it returns [TEMP:p, 1st module F=FET, C=CAP, X=Transformer, 2nd
module F=FET, C=CAP, X=Transformer]
Example <TEMP:p> returns [TEMP:1:25,27,20,26,27,28]
<BTEMP:?> Returns battery temp value in degrees C [BTEMP:nnn] nnn in degrees C, can be a negative value
<ABSORBV:nnn> Sets system wide absorb voltage nn.n = absorb voltage (all ports)
<ABSORBV:?> Returns current system wide absorb voltage [ABSORBV:nnn] (all ports)
<ABSORBT:ttt] Set system wide absorb time in tenths of hours (all ports)
<ABSORBT:?> Returns system wide absorb time in tenth of hours [ABSORBT:ttt] (all ports)
<FLOATV:nnn> Sets system wide float voltage nn.n = float voltage (all ports)
<FLOATV:?> Returns current system wide float voltage [FLOATV:nnn] (all ports)
<FLOATT:ttt] Set inverter’s float time in tenths of hours (all ports)
<FLOATT:?> Returns inverter’s float time in tenth of hours [FLOATT:ttt] (all ports)
<FIRM:p> Returns firmware revision of software for device connected to port p [FIRM:V1.V2.V3]
<FIRM3:?> Returns MATE3 firmware revision [FIRM3:V1.V2.V3]