X Rockers 51277 - Manual (Page 4)

· Lift the X Rocker out of the box by opening the top and turning the box over. DO NOT LET THE UNIT FALL OUT. Slide the box off
of the unit. Do not grab the sides of the X Rocker as that may lead to accidental speaker damage.
· Keep the chair in the folded position and place it on the floor so that the back side of the chair is touching the floor and the
bottom of the seat is facing up.
· Position the chair on the floor so that both the headrest and the foot of the seat are touching the floor. This is shown above in
the "POSITIONING FOR SECURING PIN AND VELCRO FLAP" diagram.
· Insert the included pin into the closure. Pull and secure the Velcro flap to hide the pin and the closure.
· Review the set-up diagrams to familiarize yourself with the X Rocker's components, accessories, and set-up.
· Remove all of the included accessories from the accessory pack that is included with your chair.
· Follow the diagrams below to install the pedestal and the arms.
· Carefully turn the chair over.
· Locate the input/output panel on the right side of the seat. When used in wired mode, make sure that the control panel is not
more than 9.84ft / 3 meters away from the audio source and 6.56ft / 2 meters away from a power source. When used in wireless
mode, make sure that the control panel is not more than 65.6ft / 20 meters from the audio source and 6.56ft / 2 meters from a
power source.
· Unpack the power adapter, plug it into a power outlet and connect it to the power jack (A7) on the control panel.
· Press the power button (A6) and confirm that the power indicator light (A1) is on. In wireless mode, turn on the power to the TX
box (A12), confirm that its indicator light is on, and check that the band selected on the TX box (A13) is the same as that selected
on the RX (A5) of the X Rocker.
· Follow the diagrams to connect the X Rocker to the audio source of your choice in wired or wireless mode.
· Adjust the bass and volume levels to your preference…start rocking.
· Always make sure the backrest is locked before sitting in the chair.
· Excessive use of audio equipment could lead to hearing loss.
· Children under the age of 13 should not use this product without adult supervision.
· Strictly for indoor use. Do not expose to direct sunlight, moisture or extreme temperatures.
· If the cover becomes wet, disconnect the power immediately and don't use until it is completely dry.
· Do not attempt to remove the cover or any components. Removal of the cover or tampering with components puts you
at risk for injury or death from electrical shock.
· When using in wireless mode connect the audio cable to the RX. Do NOT connect the audio input directly to the Rocker
or the device will be DAMAGED.
· The maximum input of the TX box is 1V. If the input is over 1V, the sound can become distorted or fuzzy. If the Sound
coming out of the chair is fuzzy at low volumes, lower the volume on the audio source (ex. The TV, Mp3,etc) and the
distortion should go away.
· Do not mix alkaline, standard carbon-zinc, or rechargeable Ni-cad, NiMH, etc.
· Do not mix old and new batteries.
READ BEFORE USAGE:
SET UP:
PICTURE OUT OF BOX
POSITIONING FOR SECURING
PIN AND VELCRO FLAP
SITTING POSITION
FUNCTIONS:
STEP1 STEP2 STEP4 STEP3
1 2 3 B A N D
Use Allen wrench to
tighten fastening bolt
Flip Chair upright into
sitting position
Place swivel base pole into the
mounting hole on bottom of seat
Open Chair, face it down
and secure pin and velcro
WARNING
DO NOT USE ARMS TO
EXIT THE CHAIR. DO
NOT USE ARMS TO
MOVE OR LIFT THE
CHAIR.
THEY ARE FOR GAMING
SUPPORT ONLY.
Need Help? Email: [email protected] Web: www.xfunctional.com Phone: 866.969.2603
· Foldable construction for ease of storage and portability.
· Side control panel with volume, bass control, input/output jacks, and band switch.
· Ergonomic design with full back support.
· Hardwood frame construction with dual layer foam cover for extra comfort.
· Easy to clean heavy duty upholstery grade vinyl cover.
· Wireless audio transmission
4
Arm assembly:
1. Remove arms and arm brackets from box.
2. Locate the accessory pack containing bolts and Allen wrench.
3. Place the arm bracket on the side. Put 2 bolts into the bracket
and use the pre-drilled screw holes to fasten is in place. (Don
not tighten all the way.)
4. Place the arm and hardware onto the bracket as shown in
Step 2 of the diagram. Use the predrilled hole to fasten it in
place. Tightening all the bolts using the wrench, which comes
with hardware.
5. Place plastic caps into the bolts holes. Push to fasten.
Assemble the other side using the same method.